Simple Methods for Design of Steel Gusset Plates
This paper presents two simple methods for design of steel gusset plates. In the first method, the wedge theories are applied to establish state of stress in steel gusset plates. In the...
Space Frame Experimental Behavior
Previous tests on double layer grid space frames have shown that, in some cases, significant initial forces exist. In addition, for externally determinate symmetrical tests, there was...
Preliminary Design Considerations for Flat Deployable Structures
Deployable structures are prefabricated frames that can be stored in a compact configuration, and can be easily deployed into a large-span, load-bearing space structure. The interest in...
Unistrut Space Frame Systems and Their Application
A review of the application of latticed structures is presented. The design and construction of space frames is dependent upon the availability of adequate connection systems to realize...
Trends in Development of Steel Space Structures in Japan
Trends in recent development of steel spatial structures in Japan are reviewed. Starting from reviewing early development after the World War II, structural systems such as pyramidal roof,...
Some Examples of Latticed Structures in Spain
Since the middle of the last sixties latticed structures have extensively been used in Spain to cover different large areas as factories, churches, marketplaces, exhibition palaces etc....
Elastic Stability of Non-Prismatic Columns
A matrix analysis technique for determining the elastic buckling loads for columns of general form is presented along with several numerical examples. In this technique, a non-prismatic...
Analysis of Tapered and Stepped Columns by Analogy to Cantilever Deflection
An analysis is developed for handling the buckling design of tapered and stepped columns with the aid of the so called 'amplification factors'. When these factors...
Optimum Design of Tapered Tubular Members
An algorithm for designing a tubular structural member with constant taper is presented. The design criterion is that the maximum absolute stress produced by a set of loading conditions...
Buckling Load of Tapered Columns
The basic tapered column with larger section in the center, is considered using Rayleigh-Timoshenko method. Column has linearly increasing Io with...
Buckling of Variable Cross-Section Columns
An approximate solution for the problem of buckling of variable cross-section columns, loaded by variable axial force is given, for several boundary conditions. Both the cross-section...
Parametric Study of Bracing in Lattice Towers
The behaviour of cross-bracing comprising struts and ties connected at their cross-over joints in lattice towers is subject to some uncertainty. It is affected significantly by taper and...
Design Issues in Steel Buildings
The Committee on Design of Steel Building Structures of the Committee on Metals of the Structural Division of ASCE was formed in 1981, with the express purpose of studying problems that...
Steel Girt Design
Procedures are presented for the design of light gage cold formed girts and hot rolled girts. The effects of continuity, sag rods, and wall sheeting are discussed. Design procedures are...
Floor Vibrations ? Tips for Designers
The purpose of this paper is to suggest a number of practical concepts which can be used to improve the performance of floor systems subject to occupant induced motion from either walking,...
Composite Floor Vibrations: Predicted and Measured
Several steel composite floor systems of relatively long span trusses for a number of high rise structures in the Chicago area have been subjected to field measurements to evaluate their...
Buckling of Unsymmetrical Thin-Walled Members
The formulation of a three-dimensional model based on p-version finite element method for the elastic buckling analysis of unsymmetrical thin-walled members under axial compression and...
Behavior of Cold-Formed Steel-Concrete Composite Beams
An experimental investigation was conducted at California State University - Long Beach to study the structural behavior of composite beams made of thin-walled cold-formed steel stiffened...
Cold-Formed Z-Sections Under Axial Load and Bending
The use of cold-formed Z-section members as beam-columns presents some unique design problems which are not adequately addressed in the current design specifications. If these members...
Automated Load Capacity Determination of Cold-Formed Steel Compression Members
This paper presents an automated approach for the evaluation of the axial load capacity of nine cold-formed steel sections according to the latest AISI-1986 Cold-Formed Steel Specification....
Return to search