Permanence of Chemically Grouted Sands
Test specimens were prepared with one of three uniformly graded sands of a fine gravel and injected with one of five silicate or two polyacrylic grouts. The polyacrylic grouts showed no...
An Application of Probability to Rock Slope Design
This paper describes the use of probability and statistics in the slope design process. An example is presented of a high rock slope in an open pit mine. This slope is a major concern...
Bond Check for Concrete-Filled Steel Tubular Columns
In order that a concrete-filled steel tubular column may display a maximum bearing capacity for sustaining the long-term vertical loads transferred from the steel beams to the steel tube...
Beam to Column Stress Transfer in Composite Structures
To clarify the mechanism of the stress transfer from the steel beam to the composite column through the beam-column joint, eight exterior beam column assemblies were tested under reversed...
Bond Stress of Embedded Steel Shapes in Concrete
This paper describes an investigation into the bond stress developed between steel shapes and reinforced concrete when the concrete is lightly stressed. A brief discussion of previous...
Shear Strengths of Concrete-Filled Steel Box Elements
This study evaluated the ultimate strengths as well as the effect of the ultimate composite actions of concrete-filled steel composites under combined bending, shear, and axial forces....
Composite Columns?Design and Examples for Construction
The new German standard DIN 18806, part 1 gives the rules for the design of composite columns. The general method, taking into account all the inhomogeneties of the two materials steel...
Design of Framed Steel Structures with Infill Reinforced Concrete Walls
It is a well-known fact that an infill shear wall in a frame acts as a compressive diagonal strut, giving strength and inflexibility to the frame. Recently the Architectural Institute...
Seismic Capacity Evaluation of SRC Buildings
The Japanese standard for seismic capacity evaluation of existing composite steel and reinforced concrete (SRC) buildings was introduced. As it developed, based on the previously established...
High Strength Steel
A
Measurement and Use of Shear Wave Velocity for Evaluating Dynamic Soil Properties
Geotechnical engineers have recognized in the past decade that shear wave velocity is a basic soil property and have begun to use it to characterize sites for many uses. Most notable has...
Staggered Truss Adapted to High Rise
The 34-floor Nashville Convention Center Hotel required a structural system that would overcome the tendency to vibrate in the wind. The solution was a modified staggered frame truss,...
Numerical Simulation of Soil-Pipeline Interaction in a Ground Subsidence Zone
In this paper, the flexural interaction between a buried pipeline and the surrounding soil is examined by employing a combined boundary element-finite element scheme. The flexural interaction...
KEMCOR?A Chemical and Corrosion Resistant Piping System
KEMCOR is a new underground composite pipe system designed for chemical process use in such industries which require a high degree of corrosion resistance to varying concentrations and...
Friction in Hurricane Induced Surges
Bed shear stresses induced by the flowing water are expressed by means of a friction factor for which formulas are developed for: ocean bottom, mangrove fringes and areas, forested areas...
Boundary Shear Stress in a Meandering Channel
Longitudinal and transverse velocity, bed shear, and water surface elevation were studied in a fixed-bed, meandering, laboratory channel with naturally varying, non-prismatic cross sectional...
Behaviour and Strength of Steel Frames with Semi-Rigid Connections
A research study was started at the Politecnico of Milan (Italy) to investigate the influence of the main governing parameters on the behaviour and strength of flexible frames. A sophisticated...
Nonlinear Macroscopic Finite Element Model for Masonry Walls
A macroscopic finite element model which includes both transverse shear effects and nonlinearity due to cracking has been developed for masonry. These features are accommodated using a...
Shear Design of Masonry Walls
The paper presents a summary of a research project carried out at the Swiss Federal Institute of Technology Zurich to develop a design method based on the ultimate strength of masonry...
Load-Bearing Capacity of Masonry Walls in a Critical Buckling Condition Taking Into Account the Restraining Effect of Floor Slabs
This paper studies the buckling effect of masonry walls and concrete floor slabs as a frame system. The frame is calculated according to the theory of II. order. The buckling length, the...
Return to search