The Radiological Capacity of Transport Casks Loaded in a 2-Region Non-Uniform Pattern
The radiological capacity of spent fuel storage and transport casks can be increased by the use of non-uniform cask loading. There are many possible combinations of spent fuel burnup and...
Accurate Response Analysis of Seismic Distributed Mass Systems
A dynamic analysis technique of distributed mass structures is presented with a combination of the dynamic load factor approach and the dynamic stiffness matrix method. The dynamic stiffness...
An Electronic Specification for the Earthquake Resistance Design of the Highway Bridges in Pennsylvania
An interactive C program for the seismic design of highway bridges in the state of Pennsylvania is described in this paper. The program was developed in C language on a personal computer....
Computer Implementation of Seismic Building Codes
The objective of this work is to implement the provisions of building codes current in the U.S. as well as those of other countries for the seismic resistant design of buildings. The work...
Buckling Optimization of Laminate Stacking Sequence with Strain Constraints
An integer programming formulation for the design of symmetric and balanced composite laminates subject to buckling and strain constraints is presented. The design variables that define...
Structural Optimization to Limit Natural Periods
It is necessary to limit the natural periods of some structures to control their response to dynamic loads. Floor systems with natural periods greater than approximately 0.15 seconds may...
Stiffness Optimization Methods for Lateral Systems of Buildings: A Theoretical Basis
The sizing of the members of the lateral resistance system for multi-story buildings is often controlled by stiffness requirements. In order to achieve economical buildings, it is important...
Parallel Preconditioned Conjugate Gradient Methods for Structural Analysis Problems with Multiple Loadings
This paper describes the use of conjugate gradient method for finite element problems with multiple loading cases. Specifically, we introduce a modified conjugate gradient method for the...
Source Identification and Ranking of Wet Weather Discharges in an Urban Area
A study has recently been completed to characterize the pollutant loadings to the Providence River, RI during wet weather conditions. A total of 11 land based sampling stations including...
Finite Element Studies of Block Shear for Structural Tees
Structural tees are commonly used as tension members. As a first step toward testing the adequacy of the current design codes for net section and block shear failures near the connections...
Stochastic Finite Element-Based Reliability Analysis of Dynamically Loaded Frames
This paper presents the use of the Stochastic Finite Element Method (SFEM) for reliability analysis of steel frames subjected to dynamic loading, in the context of modal superposition....
Minimum Required Lateral Stiffness of Structures
In this paper an approximate method is presented to calculate the minimum lateral stiffness required to insure global structural stability. The technique is based on setting the critical...
Limit and Post-Limit Behavior of Space Trusses
A numerical technique for the nonlinear analysis of space trusses taking into consideration such factors as load-eccentricity, initial crookedness of the member and nonlinear stress-strain...
A Kinematic Hardening and Softening Model of Concrete
In the present paper, a new loading surface calibrated by several typical uni- and multi-axial test curves is proposed. Following the associated flow rule, a relatively simple constitutive...
Inelastic Mechanisms in Dynamically Loaded Ceramics
The dynamic response of ceramic materials has been the subject of intense research in the past decade. In this paper, we succinctly describe a plate impact experiment of a star-shaped...
One Surface Model for Concrete with Non-Associated Damage Rule
The general formulation of a continuum theory for the inelasticity of concrete is derived. The internal theory of thermodynamics is used and the dissipation inequality is established....
Wave Loading Linearization for Offshore Structures
The linearization of Morison-type wave loading is to replace u|u| by cu, where u is a zero mean, stationary Gaussian random process and c is a constant. In the present study an optimal...
Myocardial Wall Stress: A Clinician's View
Definition of left ventricular (LV) wall stress is a parameter which has a valid application in clinical medicine. This paper discusses this application as it pertains to various cardiac...
Finite Element Stress Analysis of a Spinal Segment
A large number of factors need to be determined to understand the biomechanics of a surgical procedure about the lumbar spine. Some of these factors are amenable to experimental investigations...
Simulation of Head/Neck Response to -Gx Impact Acceleration
The Articulated Total Body (ATB) model has been developed to predictively simulate the head and neck response by specifying a 2-segment/2-joint system driven at the anatomical thoracic...
Return to search