Integrated Testing and Analysis
This paper represents a new approach which greatly streamlines the entire process. In those cases where finite element modeling is used without test verification, the procedure consists...
A Study of the Correlation of the Components of Instructure Motions During Earthquakes
Thirty-two buildings are selected that have all three components of motion recorded in the basement, midheight and top of the structure. The correlation coefficients of these motions,...
The Response of Steel Containment Models to Internal Pressurization
To obtain insight and data on the response of containment vessels subjected to beyond design basis accidents, four 1/32 scale steel containment models have been subjected to internal overpressurization,...
Preliminary Analysis of Large Penetration Enclosures for Containment Vessels Subject to Beyond Design Basis Loadings
Numerical simulations of the macro-deformations of the sealing surfaces (gasketed junctures) of a PWR steel containment vessel's equipment hatch subjected to accident loadings...
Major Considerations in Scale Modeling of Reinforced Concrete Containment Structures
Reinforced concrete containment structures pose unique modeling problems, especially when leakage integrity is of interest. This paper presents a general discussion of modeling considerations...
Design Verification of HVAC Duct Turning Vanes in Nuclear Power Plants
HVAC ducts in nuclear power plants utilize short radius elbow construction with turning vanes to minimize the space requirement for duct work and to reduce flow losses in the elbows. Turning...
Evaluation of the Ultimate Pressure Capacity of Rectangular HVAC Ducts for Nuclear Power Plants
Structural design criteria are presently based on the AISI Code which limits the duct panel width-to-thickness ratio to a maximum of 500 and the maximum height-to-thickness ratio to 200,...
Modeling Techniques for Seismic Analysis of Supported Systems
An automated seismic qualification process is presented which integrates the modeling and evaluation aspects of supported system design. Emphasis is placed on baseplate and joint design....
Analytical Solution of Cable Tray Hanger 3D Structural Interaction under Seismic Loading
Structural design of cable tray hangers is controlled by the Nuclear Regulatory Commission's stringent requirements of seismic analysis. A finite element space frame model...
Composite-System Approach for Seismic Analysis of Secondary Systems
An accurate and efficient method for seismic analysis of multiply supported, multi-degree-of-freedom secondary subsystems is developed. The method accurately accounts for the effects of...
A Correlation Study on the Spectrum Decomposition Method
The major elements of the Spectrum Decomposition Method (SDM) are reviewed together with its automated process for generation of in-equipment response spectra (IERS). The floor required...
Transient Fluid-Structure Interaction of a Cylindrical Tank with a Flexible Baseplate
Analytically predicted coupled natural frequencies, response functions, and transient responses are compared with measured values for a partially filled cylindrical tank subject to excitation...
Fluid Structure Interaction Analysis of a Concrete Suppression Chamber of Mark I Containment System
Recent studies have demonstrated that the interaction between a structure and fluid can have a significant influence on the response of the overall system when subjected to certain dynamic...
A Pseudo Response Spectrum Method for Mark I Loads
A pseudo base motion response spectrum method is developed to uniquely evaluate the periodic condensation oscillation and chugging drag loads that may occur on submerged structures within...
Development of Concrete Nuclear Containment (ACI 359) Code Requirements as they Relate to Probability Based Load
The historical development of the load combinations used in concrete containment is presented in the paper. These load combinations are examined and identified in the light of the reasonable,...
Stress Distribution Around the Equipment Hatch Opening of a Prestressed Concrete Containment for a PWR Power Station
Results are reported of a finite element stress analysis for the linear elastic deformation around the equipment hatch opening in prestressed concrete containment. The dimensions and form...
Containment Integrity of SEP Plants under Combined Loads
The containment designs analyzed consisted of three inverted light-bulb shaped drywells used in boiling water reactor (BWR) systems, and three steel-lines concrete containments and a spherical...
Bayesian Procedure for Evaluation of Containment Capability
The functional requirements of a steel or concrete containment is to maintain the structural integrity as well as the leak-tight integrity of its pressure boundary under specified design...
Determination of Containment Vessel Ultimate Capacity Using Nonlinear Finite Element Analysis
Analysis of steel containment vessels is normally performed using linear elastic solutions with allowable stresses specified by applicable design codes. This method gives little indication...
Containment Capability
Section 2. 0 of this report contains a description of analysis methods for the containment structure. Testing on containment models and sections of containments is described. Section 3....
Return to search