Behavior of RC Beams under Sustained Load
Experimental results of eight reinforced concrete beams under 3-month's sustained load, with the ratio of shear span to depth equal to 2.5, are reported. It is shown by tests that the...
The Canadian Approach in the Design of Wood Structures: Conversion to Limit States Design
During the early 70's, the National Building Code of Canada (NBCC) established the principle that structural design be carried out using the limit states design (LSD) method. The technical...
LRFD Provisions for Wood Bridges
A project to develop a load and resistance factor design (LRFD) edition of the American Association of State Highway and Transportation Officials (AASHTO) Standard Specifications for Highway...
Test Experience with Heavy Angle Dead End Lattice Transmission Towers
During the past three years, the Electric Power Research Institute's Transmission Line Mechanical Research Center has conducted full scale tests on three 500kV heavy angle dead end lattice...
Metal Truss Plates: Less than Full-Depth Penetration and Shear Buckling
This paper presents the results of two experimental studies on metal truss plates which are used to join members of wood trusses. The first study investigated the effect that less than...
Response of Stressed Timber T - and Box-Beam Bridges
The objective of this study is to establish the strength, stiffness, and transverse load distribution factors of stressed timber T-, Bulk T-, and Box-beam bridge systems. To achieve the...
Shear Design Guidelines for Polyester Concrete Using Recycled Plastic
Previous research on the shear behavior of steel-reinforced polymer concrete (PC) beams has been very limited and no efficient design procedures have been proposed. In all the previous...
Fatigue Damage Accumulation Under Stochastic Stress Histories
An extensive simulation study was performed to generate random Gaussian stress time histories from power spectral densities (psd's). The psd's of time histories were selected to represent...
Time-Dependent Load-Distribution Behavior of Parallel-Member Wood Systems
The effect of differential member creep on the load-distribution behavior of parallel-member wood systems is examined. Variability in the creep response of the individual component members...
A Nonlinear-Analysis-Based Procedure for Evaluating Load-Carrying Capacity of In-Plane Steel Frames
A simple method based on geometrically nonlinear analysis is proposed to evaluate the load-carrying capacity of a steel structure. The effects of material nonlinearity and residual stress...
Anchorage of Non-Metallic Prestressing Tendons
Experimental confirmation tests were conducted to evaluate mechanical and epoxy socketed anchors for fiber reinforced plastic (FRP) prestressing tendons. The studies found that a parabolically...
Steady-State Analysis of Buckle Propagation
A novel finite element technique for the analysis of buckle propagation in pipelines is presented. The propagation pressure, propagation profile, the state of stress, and deformation during...
A Generalized Approach to the Local Stability of Stiffened Plates: Part I?Mathematical Formulation
The paper describes a generalized approach for the determination of the buckling stress of stiffened plates under combination of uniform biaxial compression, in-plane bending and shear...
A Generalized Approach to the Local Stability of Stiffened Plates: Part II?Approximate Solution
The paper presents an approximate solution for the prediction of the buckling stress of stiffened plates under combined loadings. A closed form expression is presented for the buckling...
LRFD vs. ASD for Wood Structures
There is a growing preference within the structural engineering community for the adoption of reliability-based load and resistance factor design (LRFD) procedures in lieu of traditional...
Fabric Roof Design Responds to New Technologies
A combination of newer synthetic materials and advanced structural design technologies have given contemporary tensioned fabric roofs vastly improved energy performance and far greater...
Nonlinear Behavior of Northlight Reinforced Concrete Shells
The behavior of northlight shells is very sensitive to the boundary conditions at the top and bottom edges of the shell. The aim of this paper is to investigate the structural action of...
Efficient Nonlinear Analysis of Column-Supported Cylinderical Shells
This paper presents a finite element methodology for the study of geometrically nonlinear behavior of column-supported cylinder. Due to the discrete nature of the column supports, the...
Elasto-Plastic Buckling Design for Shallow Cylindrical Shells under External Pressure
Pressures providing elastic-plastic buckling conditions for thin shallow cylindrical shell panels are presented. Classical simple support boundary conditions have been adopted for the...
The Body Language of Tensile Structures
Considered to be a 'body' and its visual appearance as 'non verbal, intuitable information,' a building has a Body Language that is employed as a primary mode. Presented is an intuitive...
Return to search