Behaviour and Strength of Steel Frames with Semi-Rigid Connections
A research study was started at the Politecnico of Milan (Italy) to investigate the influence of the main governing parameters on the behaviour and strength of flexible frames. A sophisticated...
Shear Design of Masonry Walls
The paper presents a summary of a research project carried out at the Swiss Federal Institute of Technology Zurich to develop a design method based on the ultimate strength of masonry...
Load-Bearing Capacity of Masonry Walls in a Critical Buckling Condition Taking Into Account the Restraining Effect of Floor Slabs
This paper studies the buckling effect of masonry walls and concrete floor slabs as a frame system. The frame is calculated according to the theory of II. order. The buckling length, the...
Wall/Floor-Slab Interaction in Brickwork Structures
The paper summarises the results of three series of tests on sections of brickwork structure carried out with a view to determining the characteristics of wall/floor slab joints in terms...
Type C Fly Ash and Clay Stabilization
Because the soils onsite have a high swell potential, a 37 foot high retaining wall was designed with counterforts and was supported by pier foundations to limestone. In order to reduce...
Damage Tolerance Assessment of Commercial Airframes
The regulatory authorities now require that commercial transport aircraft structural design be based on a damage tolerance philosophy. A brief history of the development of the regulations...
Effect of Voids on Creep Rate and Strength
The classic macroscopic Kachanov-Rabotnov model of material damage due to voids is reviewed. Detailed analyses of bulk mechanical properties of dilutely voided materials with certain,...
Aspects of Constant Volume Cyclic Simple Shear
Data from cyclic simple shear tests comprise the foundation on which rests most of the practical applications of theoretical soil dynamics. The importance of the test derived from two...
Multi-Directional Irregular Loading Tests on Sand
In order to clarify the effects of irregular and multi-directional nature of load application on soil deposits during earthquakes, multiple series of laboratory tests were conducted on...
Cyclic and Monotonic Undrained Response of Saturated Sands
A unified picture of the undrained monotonic and cyclic loading response of saturated sands is presented. A wide range of initial states of sand are covered in order to consider a full...
Lab Measurements of Gmax Using Bender Elements
This paper describes in detail the installation and use of piezoceramic bender elements in a variety of standard geotechnical laboratory testing equipment at NGI (e. g. , triaxial, direct...
Romanesque Reused
When Union Station in St. Louis, Mo. was built in the 1890s it was the world's largest railroad station. Having been abandoned by the railroads in the 1970s, it was reopened...
Kotmale Dam and Observations on CFRD
A concrete faced rockfill dam was the type selected for the 300 ft (90 m) dam at Kotmale in Sri Lanka for reasons of economy and speed in construction. Standard design concepts were tailored...
Need a Dependable Backfill?Try a Flowable Fly Ash
Flowable fly ash is a relatively new cementitious structural backfill material. It can be used in water or in the dry and will flow into place without the usual labor-intensive activities...
Low Cement Content High Strength Concrete
The fundamental objective of this research project was to develop mix design information for structural grade concrete using high fly ash content. The fly ash used in this project was...
Foundation Design Considerations for Detroit DPM
The design loadings for support of the elevated guideway of the Detroit Downtown People Mover (DPM) consist of high vertical as well as horizontal loads. In order to simplify foundation...
Unsymmetrically Reinforced Concrete Columns
The development of column strength formulas for unsymmetrically reinforced sections has been developed in previous papers. However, aids such as interaction diagrams have not been available...
Towards Rational Design of Structural Members in Reinforced Concrete
With the increasing emphasis on cookbook designs, plug-in and punch-in formulas, and punch-in numbers in the personal computer program, there is a danger that the designer may accept the...
Advances in High Strength Concrete,
The technology for producing field placeable concrete with a 28 day compressive strength of 10,000 psi has been available for many years. With the recent use of microsilica as an additive...
State of the Art in Concrete-Polymer Materials
Concrete-polymer materials represent a relatively new technology in the construction industry. In some cases polymers are combined with portland cement concrete and, in other cases, polymers...
Return to search