Limit State Analysis of Lattice Steel Transmission Towers
The background and present status for limit state analysis of lattice steel towers at the Bonneville Power Administration is presented. Conceptual development, a computer program, and...
Engineering Mechanics in Civil Engineering
The principles of engineering mechanics and the application of these principles to civil engineering problems cover a broad spectrum of topics ranging from theory to practice. These proceedings...
Finite-Strain Axial Analysis of Piles in Clay
In the late 1970's, a series of research projects developed simple effective-stress methods to predict the axial capacity of piles in normally-consolidated clay. The method...
Centrifugal Modeling of Pile Foundations
Modeling of pile foundations in a centrifuge, where the self weight induced stresses in the soil are simulated by elevated gravity loading, is described. Hollow pipe piles in a stiff clay...
Prediction of Settlement of Single Piles in Clay
Analyses by trial were used to fit theoretical load-settlement curves to measured curves for driven piles. For the elastic method, analyses of load tests indicated that designers should...
Shaft Capacity of Driven Pipe Piles in Clay
A compilation of axial load test records for driven pipe piles in clay published by the American Petroleum Institute is analysed to yield new criteria for skin friction and pile scale...
Limiting Tip and Side Resistance: Fact or Fallacy?
The tip and side resistances of deep foundations do not reach a limit at a critical depth; instead, they increase with depth. For the tip, the rate of increase decreases with depth. For...
Residual Stresses in Piles and the Wave Equation
A data base of 18 vertical load tests on driven piles in sand is presented. On average the residual point load was 56% of the measured point load and the residual friction load 19% of...
Vertical Behavior of Two 16-Year Old Drilled Shafts
Vertical load tests were performed on drilled shafts subject to lateral confining and heaving pressures from expansive soil over 16 years. Results indicated mobilized skin friction equal...
Evaluation of P-Y Relationships in Cohesionless Soils
Four semi-empirical procedures for construction of p-y curves in cohesionless soils were developed to fit data from a particular load test or a specific set of tests on similar soils....
Evaluation of P-Y Relationships in Cohesive Soils
The practice of analyzing laterally loaded driven and bored piles often requires modeling of soil response in terms of uncoupled, non-linear unit load transfer functions. These functions,...
Lateral Load Tests of Piles in Sloping Rock Fill
A new container wharf constructed at the Port of Los Angeles features vertical prestressed concrete piles to provide both vertical and lateral support. A rockfill embankment used to allow...
A Flat-Dilatometer Study of Lateral Soil Response
The effect of flat dilatometer penetration on the lateral stress conditions in soil around the dilatometer blade and the soil response against dilatometer diaphragm deflection were investigated...
Dynamic Stiffness of Pile Groups
A number of procedures have been proposed for the dynamic analysis of complete pile foundations including group effects. Most of these introduce some sort of approximation to reduce the...
Winkler Soil Model for Axial Response Analysis of Pile Groups
In this approach, the soil is idealized as a nonlinear Winkler model for a pile group attached to a group of piles. The model can account for pile-soil-pile interaction. Pile group responses...
The Simple-Pile Approach to Pile Installation in Clays
This article describes the fundamentals of the approach and presents solutions for the effects of quasi-static deep undrained penetration of a simple solid pile on the deformations and...
Pile Foundation Movements During Construction
Two case histories concern a shipyard wharf and work bay in Los Angeles harbor and an oil refinery expansion in Sumatra, Indonesia. The case histories provide further data on the nature...
A Structural Engineering Perspective for Drilled Shafts
This commentary is an attempt to close the gap between the Building Code Requirements for Reinforced Concrete (ACE 318-83) and the design of drilled shafts. The context of design includes...
Relational Model for Computer Analysis and Design
One of the most critical elements in engineering analysis and design is data management. Relational database systems have been proven to be an excellent tool for managing the voluminous...
Advanced Graphical CAD System for 3D Steel Frames
An innovative, advanced graphical computer-aided design system, called STEEL-3D, is described. The main objective of this program is to provide the engineer with all the tools necessary...
Return to search