Computer Aided Design and Cost Estimation of Gabion Lined Channels
Rivers are a dynamic part of the hydrologic cycle. Changes in discharge, flow depth, water velocity, and meander patterns contribute to this dynamic nature. As a result, portions of a...
Water Surface Profile Computations?How Many Sections do I Need?
One-dimensional streamflow models, including standard-step models, require a sufficient number of cross sections to satisfy two needs. First, a sufficient number of cross sections must...
Simulation of River Bed Evolution Below Tsengwen Reservoir in Taiwan
An uncoupled, one-dimensional river model, capable of simulating bed evolution, hydraulic sorting and armoring under unsteady flow conditions is presented in this paper. This unsteady...
Design of Pre-excavated Scour Hole Below Flip Bucket Spillways
A number of tests were performed on a model-scale flip bucket spillway with a gravel-bed plunge pool in order to develop equations to describe the geometry of the scour hole created by...
Design of Riprap Stilling Basin for Overhanging Pipe
The rock rip-rap basin is the most common and economical method of handling the problem of scour at a pipe outlet. The advantage of the method is speed of construction, absence of the...
Bank Stability Analyses Versus Field Observations
The concept and process of stream bank stabilization design through the development and use of limiting stability curves for the comparison of existing bank height/angle combinations to...
Effect of Grain Size on Sediment Transport Calculations
The U.S. Army Corps of Engineers is currently developing a `Hydraulic Design Package for Flood Control Channels' (SAM). SAM is capable of computing sediment rating curves and stable channel...
Top Width of Pier Scour Holes in Free and Pressure Flow
The maximum top width of the local scour holes at piers is shown to be a simple function of the scour depth and the angle of repose of the bed material in water. Knowledge of the top width...
Preliminary Studies of Pressure Flow Scour
Bridges that become inundated during floods have slightly pressurized flow that impacts bridge piers and creates an aggravated scour condition. Results of two preliminary laboratory studies...
Operational and Structural Optimisation of Hydraulic Structures for Light Liquid Removal
The removal efficiency of light liquid separation schemes is determined by the hydraulic inflow conditions, the inflow fluid properties and the separator hydraulics. The relating set of...
Emergency Protection, San Luis Rey River Aqueducts
A calibrated hydraulic computer model (FLUVIAL-12) was used to predict flood damage potential at the two San Diego Aqueduct river crossings in northern San Diego County. Model results...
Design and Performance of Emergency Spillway Channel Erosion Protection?Grenada Lake Dam, Grenada, Mississippi
Grenada Lake Dam located on the Yalobusha River in northeast Mississippi is part of the Mississippi River and Tributaries comprehensive plan for flood control. The 13,000-ft-long earthfill-type...
The Study of Riprap as Scour Protection for Bridge Abutments
The purpose of this paper is to provide design guidelines for riprap protection of spill-through and vertical-wall abutments situated in floodplains. With the benefit of laboratory experiments,...
Erosion Protection at Hydraulic Structures: A Report From the Task Committee
In 1991 the ASCE Hydraulics Structures Committee formed a task committee on Erosion Protection at Hydraulic Structures. The purpose of the committee is to determine current practices in...
n Values for Shallow Flow in Rough Channels
Manning's friction factor n has been developed from flume data for very shallow open channel flow in a high-gradient channel with large bed material. n values are presented as a function...
Problems with Numerical Modeling of Gravel-Bed Rivers
Inherent to one-dimensional numerical models are the assumptions that hydraulic parameters can be assigned a characteristic average value, and that the flow is gradually varied so that...
Calibration of Manning's Roughness for a River Reach
The Albuquerque Projects Office of the U.S. Bureau of Reclamation collected water surface elevations for measured discharges for the Rio Grande and many of its tributaries to try to obtain...
Hydrodynamic Modeling for Channel Barrier Design
A two-dimensional vertically-averaged finite element hydrodynamic model was used at two scales to predict flow conditions for design of a proposed fish barrier: one for the general hydraulic...
A 2-D Numerical Model for High Velocity Channels
The hydraulic performance of a high velocity channel depends on maintaining a supercritical flow regime over specified portions of its length. Predicting the potential location of shocks...
Multi Objective Detention Outlet Control Structure
Increasing numbers of stormwater management ponds are being included in the design of urban and rural drainage projects. This is in part due to the environmental outcry to clean up our...
Return to search