Composite and Mixed Construction in Czechoslovakia
Various composite and mixed systems have been used in Czechoslovakia. Special attention is focused on design methods, effective construction, and material savings. Current developments...
Seminar Summary and Research Needs
All the papers presented in the technical sessions of the seminar are summarized and, in some cases, commented upon. The needed research in composite and mixed construction is described....
Timber Bridge Decks
The portion of the nation's 500,000 bridge decks that are made of timber has been declining for years, as the old timber ones on secondary road bridges are rebuilt, in most...
Diagnosis of Wastewater Treatment Processes
This paper presents an approach to the development of an expert system for aiding the operation of an activated sludge wastewater treatment facility. The expert system incorporates a diagnostic...
Dewatering--Avoiding Its Unwanted Side Effects
The undesirable side effects that sometimes occur when dewatering for construction or mining are presented, including: ground settlement due to dewatering; deterioration of timber piling;...
Nantucket's Endangered Maritime Heaths
Heaths, though common in northern Europe, are of disjunct distribution and limited development on the east coast of North America. In contrast, Nantucket Island, Massachusetts supports...
Sonoma County: Success Story of California's Coastal Development
The Sea Ranch second home development, agricultural and timber land preservation, the need for better commercial fishing facilities, and recreational and visual access to the coast were...
Design and Construction of Guideway: Vancouver Advanced Light Rapid Transit
The Vancouver Advanced Light Rapid Transit (ALRT), system consists of linear induction motor driven, light-weight cars automatically controlled operating over a 21. 4 km system from downtown...
Alignment Special Structures for Vancouver's ALRT
This paper describes the special long-span structures, offset columns, and bent structures used in situations where the standardized guideway components used in over 90 percent of the...
Production of Guideway Beams for the Vancouver ALRT
This paper describes the planning, layout and design of a large scale precast plant and innovations in production technology for the fabrication and delivery of 1040 tangent and curved,...
Guideway Beams?Formwork and Fabrication
A manufacturing concept was developed around an adjustable form capable of mass producing prestressed concrete beams to the unique geometric configuration of each section of track. The...
The Effect of Connection Flexibility on Steel Members and Frame Stability
With the advent of Load and Resistance Factor Design (LRFD) and the many existing moment-rotation curves for connections, the use of actual connection flexibility in the design process...
Utilization of Experimentally Obtained Connection Data in Assessing the Performance of Steel Frames
Data from over 70 separate experimental studies on steel beam to column connections are reviewed with particular reference to the joint's in-plane moment-rotation characteristic. More...
Flexibility of Steel Seismic Moment Connections
Relevant Berkeley experimental results are critically evaluated to determine the flexibility of W18 W24 beam joints with and without stiffeners and/or doubler plates. The paper discusses...
Research Needs for Extant Iron and Steel Buildings
A brief review of iron- and steel-making processes is background for the development of shapes and codes. Sources of information for the condition assessment of iron and steel buildings...
Continuum Modeling of Periodic Truss Structures
Procedures for deriving equivalent stiffnesses for an extended Timoshenko beam used to represent truss beams are presented. A typical substructure of a truss is used to calculate these...
Effect of Steel Fibers on the Cracking Behavior of Reinforced Concrete Continuous Beams
A research program was conducted with the aim of studying the cracking behavior of reinforced concrete continuous beams, as it is affected by using different combinations of main steel...
Rational Design of Beam-Columns in Steel
The paper discusses the procedure as currently recommended in the AISC Manual for selection of beam-columns in steel and points to the inadequacy of this procedure for quick convergence...
Unsymmetrically Reinforced Concrete Columns
The development of column strength formulas for unsymmetrically reinforced sections has been developed in previous papers. However, aids such as interaction diagrams have not been available...
Probabilistic Basis for Design Criteria in Reinforced Concrete
This collection of papers presents the results of research on the variability of reinforced concrete members carried out at the University of Alberta, Edmonton, Canada, during the period...
Return to search