Experiences with an Undergraduate Structural Engineering Laboratory
An Undergraduate Structural Engineering Laboratory was recently implemented at Lehigh University with funds obtained from the National Science Foundation through its instrumentation and...
Prediction of Structural Response to Large Earthquakes by Using Recordings From Smaller Earthquakes
The feasibility of predicting structural response to large earthquakes by using recorded responses from collocated smaller earthquakes is investigated. Records from large earthquakes can...
Long-Term Monitoring of Civil Structures using Smart Structures Techniques
A smart monitoring program for a hybrid concrete-steel building in Washington, D.C. has been developed. The building is currently being instrumented with a variety of strain and corrosion...
Cyclic Performance of Riveted Connections
As part of a larger experimental project on seismic performance of older steel frames, seven concrete-encased and unencased connections were tested. The specimens consisted of both riveted...
Seismic Retrofit of R/C Columns with Inadequate Lap Splices
This paper presents experimental results on the use of rectangular steel jackets to improve the seismic performance of rectangular steel jackets to improve the seismic performance of rectangular...
Compressive Strength of Large Scale HSLA-80 Steel Cellular Sections of a Double Hull Ship Structure
An analytical and experimental large scale test program was conducted to investigate the instability failure modes of cellular double hull box sections. The main emphasis of the study...
Review of Cold-Formed Steel Purlin Design
The use of cold-formed steel members as roof purlins for single story industrial and commercial buildings is commonly recognized. These members typically have either a C- or Z-shaped cross...
Column and Beam-Column Design - A World View
This paper is concerned with the design of columns and beam-columns in steel building frames. Design provisions found in some selected codes viz. AS DR87164 87(Australia), BS5950 Part...
Some Aspects of Compression Member Design in Australia
The paper summarizes and elucidates the provisions of the Australian Standard AS4100-1990, Steel Structures, for the design of compression members. Emphasis is placed on those aspects...
Phoenix Central Library: Reading Room Roof
This paper discusses the design and analysis of the cable truss roof over the fifth floor reading room of the new Phoenix Central Library. Forty pairs of diagonally oriented cable trusses...
What Controls the Ultimate Load of a Glulam Dome?
A glulam dome is analyzed with the finite element method to determine the governing failure mode and ultimate snow loads. The dome consists of a triangulated network of curved glulam beams,...
Field Measurements of Tensile Forces on a Spherical Dome Sector Caused by Internal Load of a Granular Product in Storage
Using a number of existing equations developed application to silos, bins, and hoppers, the horizontal load resulting from the stored product can be calculated. In this paper, the physical...
AWS versus AIJ Tubular K-Connection Design Rules
Among various existing design rules for circular tubular connections, the AWS rules are compared with the AIJ rules because of differences between the two. Subjects of discussion include...
The Behaviour and Design of Stressed-Arch (Strarch) Frames
The paper presents an overview of the stressed-arch structural system and the associated research program undertaken at the University of Sydney between 1988 and 1992. The objectives of...
Design of Half-Through or Pony Truss Bridges Using Square or Rectangular Hollow Structural Sections
The initial part of this paper will outline some of the research, testing, and investigation which has been done on half-through truss bridges. This research is primarily concerned with...
Research and Application of Various Joints of Space Grid Structures in China
This paper introduces the research work results and applications of various joints of space grid structures in China. It also gives out formulas for determining the loading capacity and...
Structural Tests on the Suspen-Dome System
The 'suspen-dome' system, which the authors have developed, consists of a single-layer truss dome and a cable structure. The present paper deals with the results of structural tests conducted...
Simulation Procedure for Buckling Behaviors of a Reticular Dome
Complex behaviors of the ball-joint connection, especially used in steel space structures, are expressed in the numerical model to confirm the estimative ability of such a model by comparing...
Buckling of Single Layer Latticed Dome under Uniform Gravity Load
This paper reports on experiment and numerical analysis relating the buckling of a single layer latticed dome under uniformly distributed nodal gravity load at the dome central portion....
The Georgia Dome and Beyond: Achieving Lightweight - Longspan Structures
In the last two decades, the development of longspan roof structures has undergone a quantum leap. The introduction of steel structures, fabric structures, Bucky Fuller's tensegrity structure,...
Return to search