Use of Scrap Tires to Harness Wave Energy
A 2.5 meter diameter wave powered pump, fabricated from scrap tires was tested from May 24, 1988 to October 1988 in the Atlantic Ocean at the North Carolina Army Corp of Engineers Waterways...
OTEC Sea Water Systems Technology Status
A workshop was conducted in April 1988 to provide an expert critique of the fabrication and deployment options for the seawater systems (all piping required to draw the seawater) of land-based...
OTEC Seawater Pipe Cost Comparisons
Describes a material which can substantially reduce the cost of seawater pipes and two methods for building and deploying such pipes for use in land-based OTEC installations, outfall sewers,...
A Microplane Constitutive Model for Soils
A microplane model for the inelastic behavior of soils is presented. The microscopic constitutive equations are defined independentely for a set of microplanes covering all possible orientations,...
Grouting Slip Liners: The New Inside Story
There are approximately 800,000 miles of water and sewer pipelines in the U.S. that need remedial work. About 2% need work each year, usually due to normal or accidental corrosion. Normal...
Future Freight
In 21st-century America, most long-distance cargo will be transported via pipelines linking major cities. The most versatile freight pipeline is the capsule variety, which carries cargo...
Governments' Role Relative to Public and Political Pressures
Groundwater quality is a major concern in the United States today. The body of law pertaining to the protection of groundwater quality is generally inadequate for the implementation of...
Building Moon Bases
It is widely accepted that the U.S. will begin to build a base on the moon at the turn of the century, and much of the design work has already been done. Based on papers presented at Space...
High Tech on Campus
Hannan Hall, the new laboratory building at The Catholic University of America, has a structure entirely made up of precast concrete panels and 24 in. deep double tees. The loadbearing...
Changes in Tubular Design Codes
This paper summarizes a number of changes in design provisions for tubular structures that have recently been adopted. These are the result of a number of research advances concerning...
Steel Girt Design
Procedures are presented for the design of light gage cold formed girts and hot rolled girts. The effects of continuity, sag rods, and wall sheeting are discussed. Design procedures are...
An Optimal Design of Steel Pipe Pile Foundation
This paper presents an optimal design method for the steel pipe pile foundation of bridge pier using a nonlinear programming. It is firstly assumed that an imaginary wall model behaves...
The Fatigue Performance of Welded Joints in a Marine Environment
The fatigue lives of plate-plate, pipe-plate, and tubular welded joints tested in seawater under free corrosion, optimum cathodic protection and cathodic overprotection measured in the...
Inelastic Response of Buried Pipelines Due to Landslide Effects
During earthquakes, a buried pipeline may experience significant loading as a result of large relative displacements of the ground along its length. Large ground movements can be caused...
Local Wind Pressures on Roofs
The paper reviews the results of the most recent research studies in the evaluation of wind pressure coefficients for the design of roof cladding elements. The effect of roof geometry...
Wind Effects on Loose-Laid Cladding Systems
Modern roofing systems for flat roofs frequently make use of rigid insulation boards, gravel and concrete pavers that are loose-laid on top of the waterproof membrane. The authors have...
Full-Scale Measurement on Chiba Port Tower
Chiba Port Tower is a tall tower, 125m high, with a rhombus shaped plan. All of the surfaces are covered with half mirror glass. On the top of the tower, a 'Tuned Mass Damper'...
Vibration-Induced Wind Pressure on Large Span Flat Roof
Vibration-induced wind pressures on a large span flat roof was investigated by a wind tunnel using a uniformly turbulent flow. Measurements of pressures were made on an asymmetrically...
A New Proposal of Design Wind Loads for Beams Supporting Long-Span Roofs
The wind tunnel testings of wind pressures acting on long-span roofs are carried out. Dynamic wind pressures are measured simultaneously at a lot of points on the roofs. The instantaneous...
Pressure Measuring System for Wind Loads
A project to acquire wind and building surface pressure data in the field is continuing at Texas Tech University. A test building of dimensions 30 ? 45 ? 13 ft (9.1 ? 13.7 ? 4.0 m) and...
Return to search