Concrete Pipe Trenchless Technology
Precast reinforced concrete pipe is the most commonly used pipe material for jacking operations. For over 90 years, concrete pipe techniques, procedures and applications established the...
Pipeline Design and Installation
The proceedings of the International Conference on Pipeline Design and Installation, held on March 25-27, 1990 in Las Vegas, Nevada, presents information on all aspects of pipeline design...
Sounding Out Buried Waste
Geophysical diffraction tomography (GDT) is a new remote sensing technique for quantitative high-resolution subsurface imaging. It is similar to optical holography where long wavelength...
Evaluating Spring Flow Trends at Pipe Spring National Monument and Vicinity, Arizona
A study conducted by the National Park Service Water Resources Division is resolving if ground water pumping is causing spring flow declines at Pipe Spring National Monument (PISP). Ground...
Use of Linear Programming for Hydraulics Problems
Water is becoming a more and more precious commodity worldwide with each passing day. At the same time, the optimum and most productive solutions to water control and utilization are becoming...
Pump Selection Program and a Better User Interface
Numerous highly innovative computer solutions to engineering problems are of little use to the practicing engineer because these programs are not supported by adequate user interface....
The Equivalence of Path and Node Methods for Water Distribution Network Analysis
This paper deals with the equivalence between commonly employed methods, path and node adjustment methods, for analyzing water distribution networks. The basic equations for steady-state...
Advances in Pipeline Materials
Pipelines transport water, storm run-off, process wastes, petroleum, natural gas, slurries, solids, sewage, steam and other fluids either by gravity or under pressure. Pipelines are also...
Selection of Hole Size for Fluidization Pipes
Two-dimensional fluidization experiments are performed on fine and medium coarse quartz sands at depths of 25.4 and 42 cm. Four supply pipes are used with orifice diameters of 1.587 mm...
OTEC Sea Water Systems Technology Status
A workshop was conducted in April 1988 to provide an expert critique of the fabrication and deployment options for the seawater systems (all piping required to draw the seawater) of land-based...
OTEC Seawater Pipe Cost Comparisons
Describes a material which can substantially reduce the cost of seawater pipes and two methods for building and deploying such pipes for use in land-based OTEC installations, outfall sewers,...
A Materials Study of Interleaved Bismaleimide Composites
One approach for improving damage tolerance in epoxy based composites involves interleafing of tough adhesive layers between plies of the composite prior to fabrication. Extension of this...
Design of Fiberglass Reinforced Plastic Underground Storage Tanks
The purpose of this paper is to discuss the design and construction techniques of fiberglass composite underground storage tanks. The scope of this paper is limited to the straight shell...
Time-Dependent Behavior of FRP Lintels
This paper describes an experimental investigation into the short-term and long-term behaviors of two types of T-shaped lintels made of fiber-glass reinforced plastic with polyester or...
Load-Deflection Performance of FRP Molded Grating
This research project deals with fiberglass reinforced plastic (FRP) molded grating, its properties, manufacturing materials used and appearance. Grating strength, configuration, weight...
Laboratory Fatigue Investigation of a GRP Bridge
A fatigue study of a 4.9 m glass-reinforced plastic bridge indicated a resistance to 1.6 million cycles of load without extensive damage to joints or elements. Viscoelastic creep occurred...
Bond Stress-Slip Relationships of FRP Rebars in Concrete
A newly developed type of reinforcement bar for concrete, Fiberglass Reinforced Plastic (FRP) rebar, can be used advantageously in concrete exposed to marine or corrosive environments....
Fatigue Behavior of Bond-Anchored Unidirectional Glass-FRP's
The contribution reports on the fatigue behavior of fiberglass reinforced plastic (FRP) bars, consisting of endless E-glass fibers embedded in a polyester (PE) matrix and anchored in a...
Flexural Strength of Externally Reinforced Concrete Beams
Results from tests of one rectangular and one T-beam are reported. The beams were strengthened by epoxy-bonding a 1/4 in. (6 mm) thick Glass Fiber Reinforced Plastic plate along the tension...
Bond Strength of Fiber Reinforced Plastic Bars in Concrete
In this study, 27 beam specimens were tested to determine the bond strength of fiber reinforced plastic bars (FRP) in tension. The specimens were reinforced with #4, #6, or #8 FRP bars....
Return to search