Integrated Waste Management at the Weldon Spring, Missouri Site Remedial Action Project
The diversity of contaminants and contaminated media at the Weldon Spring, Missouri CERCLA site, located about 30 miles west of St. Louis, Missouri, necessitates the formulation of integrated...
The Replacement of Penstocks at TVA Ocoee II Power Plant
The Tennessee Valley Authority (TVA) replaced the steel penstocks at its Ocoee II power plant near Ocoee, Tennessee. A total replacement was necessary because of severe corrosion on the...
Weld Overlaying with a Cavitation-Resistant Alloy
The characteristics and applications of a cavitation-resistant alloy, Hydroloy HQ913, are described. The alloy as weld overlays applied on hydropower plant components by covered electrodes...
Reliability Analysis of Weldings Considering Defects
The welds generally represent the most critical part of large structural systems, i.e. offshore structures. Hence they affect significantly the structural reliability. A realistic model...
Fatigue Reliability of Steel Structures in the Presence of Residual Stresses
An extended model for the assessment of fatigue reliability of steel structures in the presence of residual stresses is developed. The model explicitly includes the uncertainties of the...
Safety Assessment of Welded Pipelines Undergoing Large Ground Deformation
Spatial distribution and modelling of liquefaction induced permanent large ground deformation are presented. The permanent large ground displacement patterns required for the safety assessment...
An Investigation of the Mechanical and Hydrologic Behavior of Tuff Fractures Under Saturated Conditions
The mechanical and hydrologic behavior of natural-fractures in a partially welded tuff rock were investigated. Tuff cores, each containing part of the same natural fracture oriented subparallel...
Cambering of Steel Beams
Cold cambering with force in the fabrication shop is an effective and economical method of compensating for deflections of composite beams. Typical beams should be cambered for dead load...
Effects of Fabrication on Local Stress Conditions
Factors connected with fabrication that impact on the behavior of structural steel members are reviewed. Residual stresses that result from basic steel production and subsequent fabrication...
Engineering Design Concerns Regarding Steel Fabrication
The precise fabrication of structural steel pieces is an essential part of the process leading to the satisfactory erection and connection of the individual steel elements into the final...
Repair and Rehabilitation of Damaged Steel Flexural Members
In earlier years, the primary method for repairing steel flexural members was to replace the member. However, with the cost of labor and material increasing dramatically over the last...
Seismic Behavior of Built-Up Bracing Members
The influence of stitch design and local buckling on the seismic behavior of welded bracing members made of double angles is studied in this paper. Performance of boxed configuration with...
Tests on Brace and Link Connections for EBFs
This paper describes recent test results on the behavior of selected connections for seismic-resistant Eccentrically Braced Frames (EBFs). These tests provided data on the performance...
Brace Connections for Ductility
Influence of connection design on the seismic behavior of welded bracing members made of double channels is studied in this paper. Shortcomings of commonly used connection details as per...
A Summary and Review of Fatigue Data for Mechanical and Welded Splices in Reinforcing Bars
Published reports pertaining to fatigue tests of welded and mechanical splices in reinforcing bars were reviewed. It was observed that most specimens fractured in the reinforcing bar adjacent...
Fatigue Strength of Welded Steel Mesh
Welded steel mesh (WSM) is prefabricated by welding cold-drawn wires in a grid-like mesh. Engineers avoid using WSM as main reinforcement in highway structures due to their lack of knowledge...
The Fatigue Performance of Welded Joints in a Marine Environment
The fatigue lives of plate-plate, pipe-plate, and tubular welded joints tested in seawater under free corrosion, optimum cathodic protection and cathodic overprotection measured in the...
Inspection Strategies for Offshore Structures
The fatigue limit state is the governing limit state for the structural dimensions in several parts of offshore structures. Prediction of the fatigue life of tubular joints and other welded...
Effect of High Frequency Response on Fatigue of Offshore Structures
Welded steel specimens have been tested under several loading spectra to determine the effect on fatigue life of high frequency components in the psd of the stress or strain in the joint....
The Challenge of Yucca Mountain
Yucca Mountain is the most likely site for the nation's high level nuclear wastes. Congress chose the site out of three candidates for further study before designating it...
Return to search