Rigid Beam-To-Column Connection Detail for Circular Composite Columns
Steel pipes with relatively thin wall thickness and filled with high strength concrete have been used in building construction. Some of the advantages of this type of column include eliminating...
Design of Frames Using Notional Horizontal Force
The cantilever columns and portal frames are studied by using the notional horizontal force design concept. This concept intends to eliminate K-factor in the frame design. It was found...
A Nonlinear-Analysis-Based Procedure for Evaluating Load-Carrying Capacity of In-Plane Steel Frames
A simple method based on geometrically nonlinear analysis is proposed to evaluate the load-carrying capacity of a steel structure. The effects of material nonlinearity and residual stress...
Seismic Retrofit of R/C Columns with Inadequate Lap Splices
This paper presents experimental results on the use of rectangular steel jackets to improve the seismic performance of rectangular steel jackets to improve the seismic performance of rectangular...
Column and Beam-Column Design - A World View
This paper is concerned with the design of columns and beam-columns in steel building frames. Design provisions found in some selected codes viz. AS DR87164 87(Australia), BS5950 Part...
Some Aspects of Compression Member Design in Australia
The paper summarizes and elucidates the provisions of the Australian Standard AS4100-1990, Steel Structures, for the design of compression members. Emphasis is placed on those aspects...
Controlling the Seismic Behavior of Precast Concrete
Precast concrete has, through the years the years, acquired a bad reputation insofar as its ability to withstand earthquake is concerned. This reputation, though reasonably based, is not...
Seismic Performance Behavior of Precast Concrete Beam-Column Joints
The experimental test program being conducted at the National Institute of Standards and Technology on 1/3-scale model precast concrete beam-to-column connections is summarized. The objective...
Assessment and Testing of Column Lap Splices for the Santa Monica Viaduct Retrofit
This paper describes assessment and the full-scale test of a 3 ft. (914 mm) dia. column containing #11 (34.9 mm dia.) reinforcing steel lap-spliced in the critical region. The column modelled...
Seismic Strengthening of R/C Columns Using Steel Jackets
This paper presents experimental results on the use of steel collars and steel jackets as a retrofitting system to improve the seismic performance of short rectangular reinforced concrete...
Cyclic Behavior and Seismic Design of Steel Base Plates
The objectives of this study were to conduct realistic experiments to understand cyclic behavior of steel column base plates and to develop seismic design recommendations. Six specimens...
Some Unresolved Issues in Seismic Steel Codes
In the latest revisions of the three major U.S. seismic codes (AISC, NEHRP, UBC) some requirements can be questioned because of limited knowledge. Confining attention to conventional kinds...
A Wind Tunnel Study of an Aeroelastic Model of the Florida Suncoast Dome
Very large scale cable domes have been built using prestressed, high strength steel cable or strand, steel tube columns and a lightweight fiberglass skin. Geiger Engineers Florida Suncoast...
Seismic Behavior of High Strength Concrete Columns
Information on the ductility of high strength columns in seismic areas has been scarce. The available information is based mainly on small test columns subjected to monotonic concentric...
Joint Design in Composite Columns/Steel Beam Structures
The use of a composite building system, utilizing a composite exterior column and a concrete spandrel beam system, proposed by Dr. Fazlur Khan in 1967, is recalled. In the last 25 years,...
Axial Capacity of Concrete Infilled Steel Box Column with Biaxial Bending
The objective of this study was to investigate the feasibility of using the Bresler reciprocal load method to calculate the axial capacity of a concrete infilled steel box column subjected...
An Innovative Connection Detail for High-Rise Buildings
Composite columns consisting of hollow steel tubes filled with high strength concrete have been used in high rise building construction in the USA and Far East Asian countries. The focus...
Seismic Design of Steel Beam-to-Box Column Connections
This paper is a study of the ductility requirements of steel beam-to-box column connections using the bolted beam web and welded beam flange details. Since the beam moment at the connection...
Seismic Resistance of Steel Fiber Reinforced Concrete Beam-Column Joints
This paper discusses the advantages of using steel fibers in seismic resistant beam-column connections. First, the effects of fibers on the various aspects of behavior of concrete are...
The Use of Built-Up Compression Members?A Fabricator's Viewpoint
A variety of cross-sections of built-up compression members that have been used are shown. Suggested items that need to be addressed for the successful design and fabrication are discussed....
Return to search