Seawater Experimental Results of Direct-Contact Condensation for OC-OTEC Applications
Tests of a direct-contact condenser (DCC) for open-cycle ocean thermal energy conversion systems (OC-OTEC) have been conducted using seawater and exchanging up to 1.25 MWth...

A Semi-Empirical Model for an OC-OTEC Spout Flash Evaporator
A phenomenological model for the thermal-hydraulics of a spout flash evaporator is presented in this paper. The model considers the two-phase flow behavior both in the spout and in the...

Model for Nonlinear Behavior of Bolted Joints Under Bending/Tension Loading
A mathematical model to predict the load-deformation relationship of single-bolted connections in wood structures subjected to bending/tension loading is described. The model accounts...

The ENF Test: Critical Analysis and Computational Modelling
We have developed an experimental and computational strategy to moderate the experimental scatter of the interlaminar fracture toughness values (GIIc)...

Protection of Wood Designs in Adverse Environments
Engineers and architects are becoming increasingly aware of the risks of poor wood design practices and the benefits of using wood properly. This paper addresses biological factors that...

Rate Effects in the Deformation of Rocks
This paper gives a brief review of creep and rate effects on the behavior of rocks, within a wide range of confining pressures and temperatures, and with a special emphasis on the physical...

A Microplane Constitutive Model for Soils
A microplane model for the inelastic behavior of soils is presented. The microscopic constitutive equations are defined independentely for a set of microplanes covering all possible orientations,...

Creep of Polycrystalline Ice
This paper discusses the extension of creep models for polycrystalline ice to include the effects of a non-monotonic loading history. Attention is focussed on cyclic loading since it is...

Repair of an Improperly Detailed Masonry Facade: A Case History
The masonry facade of an 18-story condominium building was constructed with an inconsistent pattern of shelf angle supports, marginal lateral restraints and without any horizontal control...

Building Joint Movement
Moisture leakage in masonry claddings occurs not only through copings and facial separation cracks, but also through failed sealant joints in the veneer. The factors affecting joint movement...

Three Tools for Design Test Bed Analysis
Three analytical tools are outlined for use in design test bed work focusing on the design/production interface. The tools are substitution analysis, coupling analysis, and value chain...

An Extended Mixture Approach for Modeling of Fiber Reinforced Cementitious Materials
A rate-independent, anisotropic model for Fiber Reinforced Cementitious Materials (FRCMs) is presented. A continuum damage/plasticity model for the concrete and an effective fiber model...

Thermomechanical Damage Due to Hydration in Large Concrete Dams
This paper presents the bases of a thermomechanical model able to describe the main evolution of concrete properties with aging. The model is based on the 'maturity'...

Accurate Computation of Freezing Index
'Freezing index' (cumulative degree-days below freezing) is used for predicting frost penetration depths and modelling pavement performance. Contour maps which illustrate geographic trends...

Behavior and Strength of Telescopic Steel Shores
To study the load distribution between concrete floors and shores during construction, the non-linear axial load-shortening behavior of a single post shore must be modeled properly. In...

Stresses in Concrete Armor Units
This book is derived from a Seminar at the Waterways Experiment Station, Coastal Engineering Research Center, Vicksburg, Mississippi held on November 7-8, 1989. It presents a state-of-the-art...

Watershed Planning and Analysis in Action
This proceedings consists of papers presented at the 1990 Watershed Management Symposium held in Durango, Colorado from July 9-14, 1990. These papers present both research performed in...

More Than a Public Hearing
Too often, required community input is reduced to the sometimes dreaded public hearing. Many formal public-involvement programs are comprised of no more than this minimal, yet essential,...

Prospects for International Engineering Practice
International trade is growing in construction products and services. It is stimulated by international efforts to reduce technical barriers to trade and the formation of a single European...

Hydraulic Engineering
This proceedings consists of papers presented at the ASCE National Convention on Hydraulic Engineering given July 30 to August 3, 1990 in San Diego, California. The Conference provided...

 

 

 

 

Return to search