ASCE will be sunsetting the Civil Engineering Database (CEDB) in the coming months. We encourage you to start using the ASCE Library to perform content searches. In the ASCE Library, you can save your search results as well as receive email content alerts when new content relevant to your area of interest is published. Try it out today at https://ascelibrary.org.

 

Electrical In Situ Measurements for Predicting Behavior of Soils
A new method is presented for predicting the in situ stress-strain behavior of fine grained soils based upon in situ measurements of its electrical properties. The method involves the...

Residual Soil Settlement From Pressuremeter Moduli
The Menard pressuremeter test is briefly described, and practical drilling techniques are summarized for Piedmont residual soils. Applications and limitations of the pressuremeter are...

Pressuremeter Tests and Shoring Wall Design
Pressuremeter testing was used as an integral part in the design of the temporary tieback shoring wall for the Columbia Center office building in Seattle, Washington. Pressuremeter testing...

Probabilistic Study of SPT Liquefaction Analysis
The influence of earthquake magnitude upon the commonly used correlation between Standard Penetration Test (SPT) blow count and liquefaction potential is evaluated using a probabilistic...

Strength of Fine-Grained Soils Using the Piezocone
Evaluation has been made of several theories and methods for deducing the undrained and effective stress strength of saturated fine-grained soil from piezocone test results. Bearing capacity...

Cone Penetrometer Use on Uranium Mill Tailings
Piezocone data were found to be very reliable in the identification of uranium tailings according to the traditional categories of sands, sand-slime mixtures, and slimes by the use of...

In Situ Tests with K_o Stepped Blade
The results of field tests conducted using the K//o Stepped Blade to determine lateral stresses and other geotechnical properties are presented. The sites tested represent a wide range...

Pore Pressure Effects in Borehole Shear Testing
The effects of excess pore pressures on shear strength results obtained using the Borehole Shear Test (BST) were investigated. Pore pressures were measured during the consolidation, shear,...

Electrical Method of Predicting In Situ Stress State of Normally Consolidated Clays
The electrical method was used to characterize the electrical anisotropy, shape and cementation of fine grained soils. It was found that for normally consolidated soils there is a strong...

In-Situ Testing to Characterize Electric Transmission Line Routes
A review of the literature has shown few definitive studies which separate test variability from soil inhomogeneity. A sensitivity study was performed to evaluate the effects of the overall...

In Situ Testing of Calcareous Sand?Campos Basin
Sampling and in situ testing were used to investigate soil conditions for the installation of offshore platforms at the Campos Basin, Brazil. At these sites calcareous sand formations...

Effect of Cementation on the Cone Penetration Resistance of Sand
A laboratory study was conducted to investigate the effect of cementation on the cone penetration resistance of sand. A new apparatus to form homogeneous artificially cemented sand specimens...

Bearing Capacity of Footings on Clay CPT Method
A method is proposed to predict the ultimate bearing pressure for footings on clay using data from cone penetration tests. This method relates the ratio of ultimate soil bearing for a...

Interpretation of CPT Data for Design of Earth Dams Near Tehachapi, California
The Static Cone Penetration Test (CPT) was used to obtain needed geotechnical information for design and construction of two small earth dams near Tehachapi, California. The basic CPT...

Analysis of Liquefaction Potential by Insitu Testing
This paper describes the results of insitu testing performed to assess the liquefaction potential of a sand formation at a site for a proposed large industrial facility in East Central...

Effctive Stress Interpretation of In-situ Tests
Significant differences in terms of load-settlement curves obtained from Plate Load Tests (PLT) and q//c profiles obtained from Static Cone Penetration Tests (SCPT) at two sites with different...

In Situ Tests for Foundation Vibrations
There are several well established methods of determining shear modulus in situ and these are summarized in this paper. New techniques are being developed for in situ determination of...

Comparison Between In-Situ Test Results
Penetration tests provide a means of obtaining data from which estimations can be made of the bearing capacity, settlement and liquefaction potential of the soils tested. Empirical formulae...

North American Standard Penetration Test Practice: An Essay
The Standard Penetration Test (SPT) is the in situ mechanical soil test most used by North American geotechnical practitioners. The equipment and procedures of the test have periodically...

Use of Piezometer Cone Data
The piezometer cone is generally regarded as the most efficient tool for stratigraphic logging of soft soils. A thin pore pressure element (5 mm thick) can sense layers a few centimeters...

 

 

 

 

Return to search