ASCE will be sunsetting the Civil Engineering Database (CEDB) in the coming months. We encourage you to start using the ASCE Library to perform content searches. In the ASCE Library, you can save your search results as well as receive email content alerts when new content relevant to your area of interest is published. Try it out today at https://ascelibrary.org.

 

Simulation Procedure for Buckling Behaviors of a Reticular Dome
Complex behaviors of the ball-joint connection, especially used in steel space structures, are expressed in the numerical model to confirm the estimative ability of such a model by comparing...

Effect of Joint Rigidity on Buckling Strength of Single Layer Lattice Domes
The present paper discusses the effect of the joint rigidity on the buckling strength of single layer lattice domes, with regular three way grids, under vertical loading. The effect of...

Buckling of Single Layer Latticed Dome under Uniform Gravity Load
This paper reports on experiment and numerical analysis relating the buckling of a single layer latticed dome under uniformly distributed nodal gravity load at the dome central portion....

Membrane Structures: Technological Innovation and Architectural Opportunity
Presented is a list of materials used in building an airhouse. There are so many other moves in tensile structures and the present interest is in ETFE foils because of light transmission/cost...

The Georgia Dome and Beyond: Achieving Lightweight - Longspan Structures
In the last two decades, the development of longspan roof structures has undergone a quantum leap. The introduction of steel structures, fabric structures, Bucky Fuller's tensegrity structure,...

Helium-Supported Hangar for a Small Solar-Powered Airship
For the IGA Expo '93 the Institute for Statics and Dynamics of Aerospace Structures, University of Stuttgart, together with Stuttgart Solar e.V. developed a solar-powered airship. For...

Current State of Development and Future Trends in Employment of Air-Supported Roofs in Long-Span Applications
Considered here is the low-profile, long span air-supported roof, as opposed to the high-profile 'bubble' variety, which has seen a substantially different development and expectation....

A Practical Design and Construction of Tension Rod Supported Glazing
In designing a glass skin-covered space, for the atrium, entrance hall or other core part of a building complex, the high openness and quality requirements of the space often lead to the...

Nonlinear Behavior of Northlight Reinforced Concrete Shells
The behavior of northlight shells is very sensitive to the boundary conditions at the top and bottom edges of the shell. The aim of this paper is to investigate the structural action of...

Spatial Structures Erected out of Thin Shell Elements Fabricated on Plane Followed by Bending
The paper offers the examples of spatial structures of average spans (up to 24 m) and engineering structures made of prefabricated curvilinear elements originally having a plane form....

Ultimate Strength of R/C Cooling Tower Shell
Reinforced concrete(R/C) cooling towers are the largest, thin shell structures. It is important to assess the ultimate strength of R/C cooling tower shells subjected to wind load. In the...

Punching Shear of Reinforced Concrete Shell Structures
In reinforced concrete shells punching shear failure may take place, if heavy concentrated loads are applied. Such failure is undesirable, since it does not provide adequate warning and...

Performance and Analysis of Frames With URM Infills
The interaction of unreinforced hollow concrete block masonry (URM) infill walls and gravity load designed (GLD) frames has been studied at Cornell University. The primary goal of this...

Behaviour of Concrete Masonry Infill - Steel Frame Structures
Twenty-eight masonry shear panels infilled in steel frames were tested to ultimate strength under in-plane, horizontal loading applied at roof level. The parameters investigated in this...

Experimental Evaluation and Finite Element Analysis of Masonry-Infilled R/C Frames
Eleven tests were conducted on 1/2-scale, single-story infilled frame specimens to study the influence of the relative strengths of the infill panels and the bounding frames and the frame...

How to Optimize Light-Gage, Cold-Formed Steel Beams
The Illustrative Examples section of the AISI Cold-Formed Steel Design Manual (AISI 1989) demonstrates how to analyze a number of different cold-formed steel sections. This paper applies...

Structural Analysis for Structural Design
This paper presents a simple extension to conventional structural analysis that serves to provide additional information that is of significant use to the structural design process. Specifically,...

RC Beam-Column Element for Nonlinear Frame Analysis
Recent studies have shown that beam-column finite elements that enforce equilibrium rather than compatibility along the element are better suited for the description of the strength and...

Flange Local Buckling and Behavior of I-Sections
A simple kinematic model is proposed to determine the locally buckled shape of the compressive flange plate of I-sections subjected to pure bending or bending combined with axial thrust....

Checking of CAD Drawings for Fabrication Issues
Communication between the fabricator and engineer is crucial to the production of an economical, safe, and functional steel structure. However, the transfer of information between involved...

 

 

 

 

Return to search