Environmental Considerations in the Design of Asphalt Concrete Paving Mixtures
The design of asphalt concrete mixtures is largely based on two empirical mixture design methods. These are 'Marshall' and 'Hveem',...
Environmental Degradation of Concrete Pore Structure
This paper illustrates how Conductometric Phase Transition Porosimetry can be used to monitor changes in the pore structure of Portland Cement Concrete which result from repeated freezing...
Size Effect in Concrete Structures and Influence of Loading Rate
The size effect law models the influence of the dimensions of the structure or specimen on the failure stress. This model can be used to quantify the brittleness of failure, and determine...
Bond Stress-Slip Relationships of FRP Rebars in Concrete
A newly developed type of reinforcement bar for concrete, Fiberglass Reinforced Plastic (FRP) rebar, can be used advantageously in concrete exposed to marine or corrosive environments....
Fatigue Behavior of Bond-Anchored Unidirectional Glass-FRP's
The contribution reports on the fatigue behavior of fiberglass reinforced plastic (FRP) bars, consisting of endless E-glass fibers embedded in a polyester (PE) matrix and anchored in a...
Flexural Strength of Externally Reinforced Concrete Beams
Results from tests of one rectangular and one T-beam are reported. The beams were strengthened by epoxy-bonding a 1/4 in. (6 mm) thick Glass Fiber Reinforced Plastic plate along the tension...
Feasibility of Class C FRP Load Transfer Devices for Highway Jointed Concrete Pavements
The objective of this paper is to analyze the feasibility of using corrosion free fiberglass reinforced plastic (FRP) devices in lieu of steel tie bars in the longitudinal joints of highway...
Uni- and Bi-Axial Compressive Fatigue of Fiber Concrete
Fatigue behavior of fiber reinforced concrete is studied under uniaxial and biaxial loadings. The S-N curves and the cyclic deformations of fiber concrete are compared to those of plain...
Bond Strength of Fiber Reinforced Plastic Bars in Concrete
In this study, 27 beam specimens were tested to determine the bond strength of fiber reinforced plastic bars (FRP) in tension. The specimens were reinforced with #4, #6, or #8 FRP bars....
Measurement of Impact Fracture Toughness of FRC
Instrumented impact tests have been in use since the early eighties for studying the fracture characteristics of cement-based composites at high rates of loading. While significant progress...
Detection of Small Voids by Impact-Echo and Signal Processing
The Impact-Echo method was used to detect slab thickness, presence of small voids and reinforcement locations in a concrete slab. Studying the frequency response of the slab, it is possible...
Evaluation of High Strength Concrete by the Break-Off Method
The reliability of the Break-Off method to test inplace high-strength concrete is investigated. A total of 188 Break-Off tests and 30 standard cylinder tests are carried out for this project....
Displacement Measurement by Laser Interferometry and Image Analysis
Laser holographic interferometry was used for the evaluation of displacement fields on concrete and fiber reinforced concrete specimens. Transmission holography was used to analyze mortar...
Lime-Fly Ash-Aggregate Base and Subbase Courses
This paper describes the use of lime-fly ash-aggregate (LFA) base and subbase courses for highway pavements. This type pavement course is considered as an alternate to cement treated bases...
Theoretical Prediction of Temperature Distributions in Airfield Runway Pavements Due to Aircraft Operation
The determination of this transient temperature distribution is important in predicting the thermal effects on pavements due to aircraft operation. In this research, heat exchange at the...
Inelastic Stability of Thin Walled Metal Tubes Under Cyclic Loading Conditions
This paper is concerned with an experimental investigation on the inelastic stability behavior of thin-walled tubular specimens of steel, aluminum and stainless steel, under cyclic loading...
Behavior and Strength of Telescopic Steel Shores
To study the load distribution between concrete floors and shores during construction, the non-linear axial load-shortening behavior of a single post shore must be modeled properly. In...
Significance of Yield Surface Corner-Like Effects in Inelastic Stability Solutions
This paper presents the author's experiences with finite element prediction of the inelastic stability of steel plate structures. The implications of linear versus nonlinear...
Compressive Strengths of Lean Concretes Containing Fly Ash
The compressive strength development of lean concretes containing fly ash was evaluated. Concretes were prepared at total cementitious materials contents of 423, 517, and 564 lb/yd3...
Anomalous Structural Size Effect in Cohesive Materials Like Concrete
This contribution analyses on theoretical grounds the size effect trends in special cases where - unlike most experimental situations in fracture research - the specimen is not precracked...
Return to search