ASCE will be sunsetting the Civil Engineering Database (CEDB) in the coming months. We encourage you to start using the ASCE Library to perform content searches. In the ASCE Library, you can save your search results as well as receive email content alerts when new content relevant to your area of interest is published. Try it out today at https://ascelibrary.org.

 

High-Strength Concrete Columns in High-Rise Buildings
Strength and ductility of high-strength concrete columns were investigated by examining available test data. The results are summarized in terms of load and ductility capacities of columns....

Lateral Bracing Criteria of the Composite Braces
In order to simplify the hysteretic characteristics of diagonal steel braces, a lateral bracing problem of unbonded braces embedded in the concrete panel is treated here. Lateral bracing...

Shock-tested R. C. Slabs: Significant Parameters
Shock-tube tests of plain concrete and reinforced concrete (R. C.) slabs were performed. The influence of free water in concrete pores, emphasized in previous tests at a material level,...

Load Rate Effects on Concrete Compressive Strength
Plain concrete cylindrical specimens from six different concrete mixes, 51 mm in length and diameter, were tested in compression quasi-statically at strain rates between 10^-6/sec...

Impulsive Punching of Fiber-Reinforced Concrete Slabs
The behavior of FRC slabs reinforced with polymeric fibers (polyacrylonitrile fibers PAN) and subjected to impulsive punching is analyzed here in order to clarify to what extent the fibers...

Innovative Design of Steel Gable Frames
Common wisdom holds that conventionally designed gable frames fabricated from rolled sections cannot compete with metal building system frames fabricated from plate and bar stock, from...

FRP Box-Beams Under Long-Time Static and Fatigue Loading
This paper discusses experimental and analytical aspects of the long-time behavior of filament wound E-glass fiber reinforced epoxy-box-beams. Theoretical and experimental data are compared...

Rational Limits for Longitudinal Steel in Concrete Columns
Current limits for the amount of longitudinal reinforcement in concrete columns were established more than 60 years ago. Commercial grades of reinforcement in 1930 were about half as strong...

High-Strength Concrete Columns: State of the Knowledge
This paper consists of reported information divided into two general categories, performance of High-Strength Concrete (HSC) columns under concentric loads, and combined axial and bending...

Evaluation of Wood Floor Vibration Design Criteria
In the United States, floors in wood buildings are designed according to strength and deflection criteria under static uniform loads. With the introduction of engineered joist products...

Strength Variability of Wood Formwork Members
Failure of concrete formwork is one of the main causes of concrete construction failures. Among the main causes of formwork failure is inadequate strength. Currently there is no published...

Effects of Site Conditions of Earthquake-Resistant Design of Structures
After a brief discussion of the importance of reliable establishment of design Earthquake Ground Motions (EQGMs) for efficient Earthquake-Resistant Design (EQ-RD) of structures, this paper...

Design Guidelines for the Use of Debonded Strands
In this paper, presented are the flexural tests performed on beams containing debonded strands. Results show that debonded strands can be used reliably and safely, stipulating that the...

Development Length of Uncoated Prestressing Strand
The Federal Highway Administration is conducting ongoing research which investigates the development length of uncoated and epoxy coated prestressing strand in prestressed concrete members....

Mechanical Behavior of Dowels Embedded in Concrete
In this paper an experimental investigation on the behavior of dowels embedded in concrete is described. The dowel strength under monotonic forces with two different boundary conditions...

A Self-Balancing Laminate
A self balancing wood laminate has been developed based on the principle of orthotropic elasticity. Lumber is cut into three sections in the flatwise plane and each side member is turned...

Metal Truss Plates: Less than Full-Depth Penetration and Shear Buckling
This paper presents the results of two experimental studies on metal truss plates which are used to join members of wood trusses. The first study investigated the effect that less than...

Natural Decay Resistance of Glued-Laminated Beams
The natural decay resistance of untreated Douglas-fir heartwood specimens sampled from glued-laminated beams was evaluated using a modified agar plate test modeled after the European Standard...

The Effects of Bolt Over-Tightening on Bolted Connections
This paper describes a portion of the research program being conducted on structural connectors which have been over-tightened. Direct-Tension Indicators (DTI) may be specified for use...

Externally Stiffened I-Beam to Box-Column Connections
This paper is concerned with I-beam to Box-column connections stiffened externally. Experimental and theoretical findings on full-scale connection models are highlighted. The performance...

 

 

 

 

Return to search