Marginal Wharf and Embankments?Seismic Design
This paper presents some of the seismic considerations used for the improvements at Berths 225 to 229 at the Port of Los Angeles. The design of the improvements was complicated by the...
Lifeline Seismic Risk Analysis?Case Studies
These papers employ design concepts and procedures in lifeline seismic risk analysis. Two of the papers describe the seismic hazards in the northwestern United States. A systems model...
Effectiveness of Highway Safety Improvements
This book contains the thirty papers presented at the third Highway Safety Specialty Conference sponsored by the Committee on Traffic and Safety of the Highway Division of the American...
Expert Systems in Civil Engineering
The importance of expert systems, also referred to as knowledge based expert systems, has been growing in all areas of civil engineering practice. The papers in this book were presented...
Building Motion in Wind
The trend towards higher structural efficiency and hence lower cost has resulted in a generation of lighter and more flexible buildings with a lower inherent capacity for energy dissipation...
Settlement of Shallow Foundations on Cohesionless Soils
Design and Performance
The main objectives of this book are to present some of the available techniques for estimating the settlement of shallow foundations on cohesionless soils, and to compare predicted and...
Asphalt Pavement Modifiers
Modifiers or additives to asphalt concrete pavements are being researched or marketed by many major chemical firms. Modifiers or additives are used to stiffen the asphalt in hot weather...
Superminis for Super CAD
Many second time users of computer-aided design software and hardware, in their efforts to have more power and flexibility, are switching to superminicomputers and building their own systems....
CAD Goes into Analysis
In the past, computer analysis of a design was always a separate and distinct step from CAD. Now, an increasing number of systems are combining the two. One system, SSCAD, allows the engineer...
CAD Mapping Trailblazer
Until three years ago, few civil/surveying firms had automated both surveying (including digital recording of angles and distances shot in the field) and the related design and drafting....
Use of In Situ Tests for Foundation Design on Clay
Years of evaluated experience with the field vane test in soft clays have resulted in empirical correction factors well suited for design practice. An extension of L. Bjerrum's...
Pressuremeter and Foundation Design
The design of shallow and deep foundations on the basis of pressuremeter results is analyzed using numerous load tests and case histories. The foundations are shallow footings subjected...
Use of SPT and CPT Tests for Evaluating the Liquefaction Resistance of Sands
A cone penetration test (CPT)-liquefaction resistance relationship has been established using the large body of standard penetration test (SPT) data. Factors for relating CPT tip resistance...
Dilatometer Tests for the Design of Grouted Piles in Rock
A case study of drilled and grouted piles in rock, which were analyzed using results of down-hole dilatometer tests is presented. The tests were performed from a jack-up platform in water...
Pressuremeter Tests and Shoring Wall Design
Pressuremeter testing was used as an integral part in the design of the temporary tieback shoring wall for the Columbia Center office building in Seattle, Washington. Pressuremeter testing...
Laboratory and Field Evaluation of Cone Penetrometers
Cone penetrometers from 8 organizations have been studied by performing laboratory tests and field tests. The testing show that pore pressure and temperature zero shift affect significantly...
In-Situ Testing to Characterize Electric Transmission Line Routes
A review of the literature has shown few definitive studies which separate test variability from soil inhomogeneity. A sensitivity study was performed to evaluate the effects of the overall...
Effect of Cementation on the Cone Penetration Resistance of Sand
A laboratory study was conducted to investigate the effect of cementation on the cone penetration resistance of sand. A new apparatus to form homogeneous artificially cemented sand specimens...
Design Parameters for Grouted Piles in Rock From In-Situ Load Tests
A series of pile load tests were performed at an onshore site to develop final geotechnical parameters for the Gaviota platform foundation which consists of large diameter drilled and...
CPT/DMT QC of Ground Modification at a Power Plant
The use of 908 static cone penetration test (CPT) and 33 Marchetti dilatometer test (DMT) soundings provided the quality control (QC) needed to improve a power plant site by the use of...
Return to search