Screening Old Offshore Platforms: Previous Approaches and Further Thoughts
Several possible levels of analysis are identified, each leading to both quantitative (economic) and subjective (human) risk evaluations. These range from ratings based only on historical...
The U.S. Naval Facilities Offshore Platform Inspection, Maintenance, Repair and Rehabilitation Program
The Department of Defense (DOD) owns many offshore platforms in various worldwide locations. These platforms are presently being utilized for training and long term research and development...
Cyclic Behavior of a Deepwater Normally Consolidated Clay
A comprehensive advanced laboratory testing program was undertaken to study the cyclic behavior of clays under various combinations of one-way and two-way cyclic loading. This work was...
Pipeline Storm Behavior on Clay Soils
A series of transverse wave loading tests was conducted on a specially mounted section of pipe in a sediment-filled tank, to investigate the stability of unburied submarine pipelines under...
Upper Bound Limit Analysis of Deep Skirt Structures' Foundations
A solution to the problem of determining the bearing capacity of an embedded footing (foundation) subjected to arbitrary loading is being presented herein. It is primarily intended for...
Three-Dimensional Circulation Modeling of the Coastal and Ocean Environments
Incursion of the loop current, a meandering feature of Gulf of Mexico large-scale circulation, may produce large hydrodynamic forces on the offshore structures. The present study is to...
A New Concrete Armor Unit for Breakwaters: The Beta Block
The aim of this paper, is to present a new artificial block for the protection of breakwaters. This armor unit, named BETA, has been designed and tested in the Coasts and Harbors Studies...
Hydraulic Design of Offshore Breakwater in Sergipe, Brazil
A Petrobras (Petroleo Brasileiro S.A.) marine terminal was recently constructed in Sergipe, Brazil (Figure 1). The offshore breakwater was initially designed in a conventional way, but...
Corrosion Fatigue of Deepwater Offshore Materials
Evaluation of the fatigue life of offshore structures operating in depths of up to 10,000 feet (3,048 m) requires knowledge of the combined effect of axial and hydrostatic loading on the...
Stability of Accropode(R) and Comparison with Parallelepipedic Block
This paper describes the tests which were performed on physical models with irregular waves, to determine the hydraulic stability of the Accropode(R)...
Experimental Research on Groyne Stability Under Very Oblique Wave Action
Most of the experimental research concerning the stability of coastal structures is focused on normal wave incidence. However, many of these structures are subject to waves which run predominantly...
Application of Fracture Mechanics Methodology to Assessment of Weld Defects in Offshore Platforms
This paper demonstrates an application of both deterministic and probabilistic fracture mechanics methods to assess weld defects in an offshore platform. The results of the assessment...
Simplified Methods for Assessment of the Structural Integrity of Existing Steel Jacket Platforms in the Gulf of Mexico
This paper presents the results of research to define a practical procedure for assessment of the structural integrity of existing steel jacket platforms in the Gulf of Mexico. An overview...
Use of Manned Submersibles to Investigate Slumps in Deep Water Gulf of Mexico
The Johnson-Sea-Link manned submersible was used to investigate surface slumps in the deep water Gulf of Mexico. High quality and specifically placed seafloor cores, video tapes, 35 mm...
Skin Friction Distrtibutions on Piles in Sand
Presented in this paper are early results from an analytical investigation of the performance of a closed-ended pipe pile under monotonic axial loading in dense sand. The study was performed...
Review of API Guidelines for Pipe Piles in Sand
Most offshore structures are supported using steel pipe piles which are designed in accord with API Recommended Practice 2A. The guidelines for analysis of axial capacity of steel pipe...
Homopolar Pulse Butt Welding of API 5L Line Pipe
Homopolar pulse welding (HPW) is a welding process that is being investigated as a means to rapidly join API line pipe, having particularly great potential for application in deepwater...
Effects of Freezing on Impact Properties of RTM Composites, and Their Applications in Offshore Structures
Resin transfer molding is rapidly being acknowledged as the process with potential to create perhaps the purest form of a composite material as representative of the concept of `material-by-design.'...
Mobile-Bed Physical Model Tests for the 1992 Olympic Harbour
The undistorted physical model is described which allowed the measurement of the wave induced velocity field along the main breakwater, and also in Somorrostro Beach (Barcelona). The current...
Dynamic Design of Deepwater Bottom-Founded Towers
This paper traces the development of dynamic design techniques for deepwater bottom-founded towers by the following: the classification of bottom-founded towers as either `stiff' or `compliant';...
Return to search