IRRICAD ? Computerized Irrigation Design
IRRICAD is a software program that helps irrigation designers by using a computerized systems approach to design. The program features drawing CAD input, interpolation of elevation data,...
CPIVOT v 2.0 Center Pivot Analysis and Design Software
A micro-computer based software package is presented which can be used for hydraulic design and/or analysis of center pivot irrigation systems. The software is written in C and requires...
Density Fluctuations and Use of the Krypton Hygrometer in Surface Flux Measurements
The magnitude of the of the Webb et al. (1980) density corrections on water vapor fluxes due to the flux of sensible heat is examined in terms of the Bowen ratio. The correction due to...
Siting Agricultural Weather Stations
Studies were conducted in Arizona and Washington to investigate how the surrounding fetch affects data collected by agricultural weather stations (AWS). AWS surrounded by extensive areas...
Steel Penstocks
Mechanism of Air Entrainment in Spillway Aerators
The mechanism of air entrainment in the Nappe over spillway aerators was investigated. Turbulence was identified as the main agent for aeration. It was found that Nappe underpressure influences...
Hydraulic Analysis of the McCook Outlet Manifold
A 1:40-scale model of the proposed McCook Outlet Manifold was tested at the U.S. Army Engineer Waterways Experiment Station (WES). Subsequently, flow conditions in the manifold were calculated...
A Model for Low-Drag Landslides
Field observations and experimental records indicate that the primary mode of motion of many large landslides is that of sliding rather than flowing. Most of the shear during sliding is...
Hurricane Andrew in South Florida: Preparing a Water Management System for Disaster
This paper analyzes Hurricane Andrew from its beginning as a tropical storm to the powerful force that it later became. The careful monitoring that took place throughout its transformation...
Computational Hydraulics?The Systems Approach
This paper introduces two modern computational hydraulic computer programs that combine the calculated subcritical and supercritical water surface profiles and pressure gradients in open...
Top Width of Pier Scour Holes in Free and Pressure Flow
The maximum top width of the local scour holes at piers is shown to be a simple function of the scour depth and the angle of repose of the bed material in water. Knowledge of the top width...
Preliminary Studies of Pressure Flow Scour
Bridges that become inundated during floods have slightly pressurized flow that impacts bridge piers and creates an aggravated scour condition. Results of two preliminary laboratory studies...
Pressure Relief Under Hydraulic Jump Stilling Basins
Gravity drainage cannot be used for any portion of a structure located below tailwater level. Yet, drainage of this area may be required to relieve sub-floor pressures and reduce the risk...
Wind Induced Circulation in Shallow Lakes
Clear Lake is a relatively shallow lake in Northern California. Natural flows are small but at times they do transport heavy metals into the lake. In order to predict water quality constituent...
Friction Loss Equations for Hydropower Facilities
Many water suppliers are pursuing economic benefits from water supply and distribution systems through development of hydropower facilities on pipelines. Excessive pressure head that used...
Hydraulic Modeling of High Unit Discharge Energy Dissipators
The incorporation of an efficient and economical energy dissipation device is critical with respect to the safe operation of a high unit discharge spillway. The development and design...
Determination of Pulsating Pressures for Baldhill Dam, N.D. Spillway
Model tests of the existing Baldhill Spillway were conducted with symmetrical and asymmetrical gate openings to determine for various flow conditions the characteristics of the hydraulic...
Three-Dimensional Modeling of Tides and Wind-Waves
A third-generation coupled discrete numerical wave prediction model is dynamically linked to a three-dimensional hydrodynamic model. The effects of water level, currents, and bottom friction...
Sliplining: Design and Installation Considerations for Polyethylene Pipe
The design methodology and installation procedure for polyethylene slipline renewal are discussed. When designing there are two critical phases which must be considered: (1) short-term...
Structural Design on Ductile Iron Pipe
The thickness class designation for Ductile Iron pipe has been changed to a pressure class designation in the 1991 revision of the C150/A21.50 ANSI standard. However, the same conservative...
Return to search