Bearing Capacity of Footings on Clay CPT Method
A method is proposed to predict the ultimate bearing pressure for footings on clay using data from cone penetration tests. This method relates the ratio of ultimate soil bearing for a...
In Situ Measurement of Permeability in Soft Clays
As part of an extensive field programme, the magnitude of errors due to clay remoulding and filter clogging in tests performed in common piezometers is evidenced. Comparisons between variable...
Skin Friction Evaluated From Friction Meter Test
This paper first describes the features of a specially developed friction meter and its operation method, and then reports in-situ test results conducted on various types of soils at two...
Uplist Capacity of Pile Foundations Using CPT Data
Southern California Edison Company has performed field uplift load tests on concrete driven piles, cast-in-place straight shaft piles and cast-in-place belled piers along transmission...
The Mudslide Profile Method to Measure the Undrained Shear Strength of Muds
Mudslides have been reported to have a very distinctive profile. Using this distinctive profile, a method is presented to analyze the stability of the mudslide at limit equilibrium conditions....
Vane Shear Testing for Staged Construction
Staged construction was used for the earthfill embankment of Birch Dam in order to compensate for low strength clays in the foundation. Sampling and testing of foundation soils verified...
Interpretation of CPT Data for Design of Earth Dams Near Tehachapi, California
The Static Cone Penetration Test (CPT) was used to obtain needed geotechnical information for design and construction of two small earth dams near Tehachapi, California. The basic CPT...
Seepage Studies Using Tracers and the Self Potential Test
Mill Creek Dam, a homogeneous silt structure resting on a conglomerate foundation, has experienced severe 'seepage since its construction in 1941. In 1981, a concrete cutoff...
Analysis of Liquefaction Potential by Insitu Testing
This paper describes the results of insitu testing performed to assess the liquefaction potential of a sand formation at a site for a proposed large industrial facility in East Central...
A Relationship Between Deformation Modulus and SPT N for Gravels
The results of over 200 horizontal plate load tests performed in situ in large diameter boreholes on gravels at various relative densities are used to develop a relationship between deformation...
The Use of Cone Penetrometer Testing to Investigate Sand Fill Subsidence Beneath Highways
During construction of Interstate I-10 between Baton Rouge and LaPlace, Louisiana, highly organic swamp deposits were excavated and replaced with hydraulically pumped river sand. The main...
Effctive Stress Interpretation of In-situ Tests
Significant differences in terms of load-settlement curves obtained from Plate Load Tests (PLT) and q//c profiles obtained from Static Cone Penetration Tests (SCPT) at two sites with different...
Fast, Economical, Cone Testing of River Sediments
The objective of the study reported was to obtain quantitative geotechnical information over many square miles of Hudson River bottom. A hand held cone penetrometer was selected for use....
In Situ P and S Wave Velocity Measurement
A review of the in situ techniques to measure P and S wave velocities by seismic wave propagation is presented. A relatively new technique, the suspension PS logging method, is described...
In Situ Tests for Foundation Vibrations
There are several well established methods of determining shear modulus in situ and these are summarized in this paper. New techniques are being developed for in situ determination of...
N-Values Used to Predict Settlements of Piles in Egypt
A method is proposed for using the standard penetration N-values to predict the load-settlement curves for different piles used in Egyptian soils. The method is based on H. G. Poulos-E....
Initial Results From an In-Situ Consolidometer
An In-Situ Consolidation Evaluation Device (ICED) was developed for field measurement of consolidation parameters by electro-osmosis. A brief description of the test apparatus and the...
Comparison Between In-Situ Test Results
Penetration tests provide a means of obtaining data from which estimations can be made of the bearing capacity, settlement and liquefaction potential of the soils tested. Empirical formulae...
North American Standard Penetration Test Practice: An Essay
The Standard Penetration Test (SPT) is the in situ mechanical soil test most used by North American geotechnical practitioners. The equipment and procedures of the test have periodically...
Use of Piezometer Cone Data
The piezometer cone is generally regarded as the most efficient tool for stratigraphic logging of soft soils. A thin pore pressure element (5 mm thick) can sense layers a few centimeters...
Return to search