Perimeter Load Transfer in Drilled Shafts in the Eagle Ford Formation
Results of six full-scale compression loading tests at four sites in the Dallas area are considered. Compressive strengths (qc) of the rock varied...
On the Elasto-Plastic Behavior of an Unsaturated Silt
Due to technical difficulties related to the control and measurement of the suction in unsaturated soils, few experimental data on the mechanical behavior of those soils exits. The paper...
Strength Design for Reinforced-Concrete Hydraulic Structures
A Review of Design Criteria for High RCC Dams
The 1980s could be considered to be the decade during which roller-compacted concrete dams came of age. This economic method of construction is sufficiently proven that very large dams...
Designing Reinforced Rock
The reinforced rock arch design method has been used to stabilize coal mine excavations for 40 years, but so far has been applied to only a few tunnels. The use of rock reinforcement develops...
Application of a Dolos Structural Design Procedure
Dolos concrete armor units are widely used to protect coastal structures. New developments in armor unit strength design permit the armor unit designer to optimize the dolos parameters...
A Critique of the Ultrasonic Pulse Velocity Method for Testing Concrete
The pulse velocity method is the most widely used ultrasonic nondestructive method for assessing concrete quality. However, it has been well established that the relation between ultrasonic...
Evaluation of Compressive Strength for High-Strength Concrete by Pulse Velocity Method
Development of compressive strength and pulse velocity for high-strength concrete from the age of 5 hours are studied in relation to cementitious material types and curing conditions....
Pullout Testing of High-Strength Concrete Members
An experimental investigation of a high-strength concrete mixture was undertaken to measure and evaluate pullout and compressive strength properties. Two columns, a slab, and cylindrical...
Collective Excellence
Building Effective Teams
Bayesian Reliability Updating of Existing Steel Girder Bridges
Bayesian statistics is used to update the reliability of existing composite steel girder bridges. A 60 ft. long simply supported superstructure is considered. The reliability for the ultimate...
Quantitative Stereology of Concrete Microcracking
Stereological methods enable extrapolation of quantitative microcrack characterization from two dimensions to three dimensional space. However, because these quantifying techniques are...
Constitutive Modeling and Simulation of Energy Absorbing Polyurethane Foam Under Impact Loading
The compressive-stress strain response of polyurethane foam under uniaxial compressive impact loading has been studied. The development of a uniaxial constitutive model from strain rate...
Debonding of a Inhomogeneity from a Plastic Matrix
Inclusion debonding is addressed through the formulation and solution of the planar elastic and elastic uniform plastic problems. These problems are variants of the standard transformation...
Direct Tensile Test: Stability and Bifurcation
Unnotched specimens of quasibrittle materials that exhibit post-peak strain softening do not deform symmetrically in a direct tension test. The phenomenon (which is similar to the recently...
Two-Dimensional Statistical Micromechanical Models for Microcracked Brittle Solids
Recent development undertaken by the authors in two-dimensional statistical micromechanical models for brittle solids with randomly located interacting microcracks is presented. Overall...
The Initiation of Bifurcations and Localization in Damaging Materials
Criteria for diffuse and discontinuous bifurcations have previously been developed and used to investigate the initiation of necking and localization in elastic-plastic materials. In this...
Softening Models for Concrete: Stability and Uniqueness
A microstructurally-based, numerically oriented, fracture-induced softening model for concrete is presented. Rate-dependent evolution equations for microcrack nucleation, growth, and coalescence...
Automated Identification of Compression-Induced Cracking in Cement Paste
The development of image analysis techniques to identify cracks using scanning electron microscope images of hydrated cement paste is described. Cracks are identified based on both the...
Contact Induced Damage
Contact induced damage is an important source of potential failure of engineering components. The particular applications where this damage occurs are in the automotive, aerospace and...
Return to search