ASCE will be sunsetting the Civil Engineering Database (CEDB) in the coming months. We encourage you to start using the ASCE Library to perform content searches. In the ASCE Library, you can save your search results as well as receive email content alerts when new content relevant to your area of interest is published. Try it out today at https://ascelibrary.org.

 

Shaft Considerations
Jacking and receiving shaft locations should be selected to minimize the number of shafts and disruptions while not exceeding the practical limits of the drive lengths achievable for a...

Pipe Characteristics
Microtunneling pipe should meet the following general requirements: Circular shape with a flush outside surface (including at the joints); Strength sufficient to withstand both the installation...

Pipe Design
The pipes and joints, once installed, must be capable of safely withstanding, for the project design life, all in-use service loads, including those associated with the following factors:...

Field Aspects
As soon as practical after their arrival at the project site, all pipes, fittings, and appurtenances should be thoroughly checked for compliance with the contract documents and accepted...

Shafts/Temporary Structures
Shafts should be of a size to accommodate the equipment and pipe selected and to allow for safe working practices. If the shaft must accommodate the permanent works, it is the contractor's...

Performance Limits for Deepwater Pipelines
This paper highlights the differences between onshore and offshore pipeline design. It then summarizes the results of combined external pressure, tension, and bending testing on full scale...

Axial Load Capacity of Pipe Piles in Sands
The axial load capacity of driven, open-ended, steel pipe piles in cohesionless soils, is often estimated using a method such as the American Petroleum Institute Recommended Practice 2A...

Behaviour of Open-Ended Pipe Piles in Sand During Installation and Loading
An experimental study was performed to investigate the physical processes which influence the axial load capacities of open-ended steel pipe piles in sand. A double-walled pipe pile was...

Performance of Suction Caissons in Sand and Clay
The use of suction caissons (suction piles) in marine environments has been increasing in the last decade. A suction caisson is a steel pipe with an open bottom and a closed top that is...

Shear and Interface Strength of Clay at Very Low Effective Stress
Thin-specimen direct shear (TSDS) tests were conducted to measure the shearing strength of kaolinite, and interface strengths between kaolinite and acrylic plastic and anodized aluminum,...

Axial Capacity of Steel Pipe Piles in Clay
Development of theories for the prediction of the axial compressive and tensile load capacities of driven piles is made difficult by a variety of factors, e.g., disturbance of the soil...

Advanced Fracture Control Procedures for Deepwater Platforms and Compliant Towers
This paper describes an integrated approach to fracture control problems � applied first as a necessary adjunct to the authors' own engineering practice, then in developing...

Design and Installation of Auger Steel Catenary Risers
The Auger export pipelines are connected to the TLP by steel catenary risers (SCRs). This is believed to be the first time steel pipe has been used for catenary risers. SCRs offer advantages...

Enhanced Detection and Mapping of Buried Utilities�A Sustainability Perspective
The social and environmental impacts and benefits of projects make up the triple bottom line that represents a modern view of sustainable project development. Rather than considering only...

Geo-Hubei 2014 244-255
Sustainable Civil Infrastructure, Innovative Technologies and Materials
Selected papers from the proceedings of the Geo-Hubei 2014 International Conference on Sustainable Civil Infrastructure, held in Yichang, Hubei, China, July 20-22, 2014. Sponsored by the...

Sinkhole Investigation and Grouting: Novel Recommendations for a Pipeline Right-of-Way
In 2009, numerous sinkholes developed within and adjacent to a 400-ft-long section of high-pressure, petroleum pipeline right-of-way that crosses under a local creek in Plymouth Meeting,...

Raise the Bar for Engineering - Extended Version
Promotional material for the Raise the Bar initiative, which seeks to require future professional engineers to obtain a Master's degree in engineering or an equivalent30 credit...

Journal of Nanomechanics and Micromechanics
The Journal of Nanomechanics and Micromechanics brings science and applications together on nanoscale and nanostructured materials, with emphasis on mechanics, processing, characterization, design, modeling,...

Building Code Requirements and Specification for Masonry Structures
Containing Building Code Requirements for Masonry Structures (TMS 402-11/ACI 530-11/ASCE 5-11), and Specification for Masonry Structures TMS 402-11/ACI 530-11/ASCE 6-11), and Companion Commentaries
Building Code Requirements and Specification for Masonry Structures contains two standards and their commentaries: Building Code Requirements for Masonry Structures (TMS 402-11/ACI 530-11/ASCE...

Existing Sewer Evaluation and Rehabilitation
Fully revised and updated, this authoritative volume offers the most comprehensive information available on maintenance, repair, rehabilitation, and replacement of existing sewers. This...

 

 

 

 

Return to search