Integrated Testing and Analysis
This paper represents a new approach which greatly streamlines the entire process. In those cases where finite element modeling is used without test verification, the procedure consists...
Tension Tests of Containment Wall Isolated Liner Plates
Two tests were conducted using an approximate 2:1 ratio of hoop to meridional load. This simple load ratio is a gross approximation of the liner plate loading in a containment subjected...
Design Verification of HVAC Duct Turning Vanes in Nuclear Power Plants
HVAC ducts in nuclear power plants utilize short radius elbow construction with turning vanes to minimize the space requirement for duct work and to reduce flow losses in the elbows. Turning...
Evaluation of the Ultimate Pressure Capacity of Rectangular HVAC Ducts for Nuclear Power Plants
Structural design criteria are presently based on the AISI Code which limits the duct panel width-to-thickness ratio to a maximum of 500 and the maximum height-to-thickness ratio to 200,...
Strength and Stiffness Characteristics of Steel Ladder-Type Cable Trays
Ladder-type cable trays identical with the as-built are generally tested to establish their strength and stiffness characteristics. Test data for systems in operating plants, however,...
Vibration Isolation of Cable Tray Hangers
Analytical and experimental investigations have been performed to partially evaluate the feasibility of using much more flexible support systems than those presently used to support electrical...
Piping Analysis: A Flexibility Approach
Design for the vertical and horizontal accelerations associated with a seismic event coupled with low allowable loads on equipment are two primary contributors to the current situation....
Composite-System Approach for Seismic Analysis of Secondary Systems
An accurate and efficient method for seismic analysis of multiply supported, multi-degree-of-freedom secondary subsystems is developed. The method accurately accounts for the effects of...
A Correlation Study on the Spectrum Decomposition Method
The major elements of the Spectrum Decomposition Method (SDM) are reviewed together with its automated process for generation of in-equipment response spectra (IERS). The floor required...
A Pseudo Response Spectrum Method for Mark I Loads
A pseudo base motion response spectrum method is developed to uniquely evaluate the periodic condensation oscillation and chugging drag loads that may occur on submerged structures within...
Stress Distribution Around the Equipment Hatch Opening of a Prestressed Concrete Containment for a PWR Power Station
Results are reported of a finite element stress analysis for the linear elastic deformation around the equipment hatch opening in prestressed concrete containment. The dimensions and form...
Structural Performance Predictions for Liner Plates on Nuclear Facilities
The history of the use of liner plates is presented. It is shown that the liner plate can be buckled, and can be bonded or not bonded to the concrete. The buckled plate usually has bending...
A Case Study in Low-Level Radioactive Waste Storage
Capital funds have been appropriated for the design, engineering, and construction of an interim low-level radioactive waste storage facility. This project is currently in the preliminary...
Safety Investigations of Existing Spent Fuel Storage Structures for Increased Spent Fuel Storage Capacity
Delays in the solution of disposal problems continue to create the need for additional on-site spent fuel storage capacity at commercial nuclear power generating facilities. Rod consolidation...
Containment Capability
Section 2. 0 of this report contains a description of analysis methods for the containment structure. Testing on containment models and sections of containments is described. Section 3....
Simplified Design of Flexible Expansion Anchored Plates for Nuclear Structures
The following two phases of the design of expansion anchored plates are discussed in this paper. a) Initial Design. b) Reassessment of as-built conditions. Initial design refers to the...
Evaluation of Non-Ductile Drilled-in Expansion Bolts
This paper provides background and justification for the design of closely spaced non-ductile drilled-in expansion bolts (bolts). It describes testing used to establish allowable design...
A Computer Integrated Engineering System for Nuclear Plant Design
The design, construction, and licensing of nuclear power facilities is a long and complicated process which can span a time period of over ten years. This tremendous lead time to plant...
An Estimate and Evaluation of Design Error Effects on Nuclear Power Plant Design Adequacy
An estimate by the author is found of typical error levels contained in Structural-Mechanical-Civil Design and Stress Reports. Based on the original analysis performed to demonstrate design...
Limit State Analysis of Lattice Steel Transmission Towers
The background and present status for limit state analysis of lattice steel towers at the Bonneville Power Administration is presented. Conceptual development, a computer program, and...
Return to search