Recent Trends and Advances in Bulk Cargo Unloading
The progress in loading of bulk cargo into ships has matched the advances in ships' size. The same could not be said for getting bulk material out of the hold of a ship, in...
Capacity Rating of Existing Piers and Wharves
This paper outlines a method for physically surveying the present material condition of existing piers and wharves and assigning to them a safe rated capacity expressed in displacement...
Seismic Design of Earth Retaining Wharf Structures
Seismic design considerations pertinent to earth retaining wharf structures are reviewed. These considerations include: evaluation of the seismic environment and design earthquake ground...
Marginal Wharf and Embankments?Seismic Design
This paper presents some of the seismic considerations used for the improvements at Berths 225 to 229 at the Port of Los Angeles. The design of the improvements was complicated by the...
Geotechnical Aspects of Stiff and Hard Clays
This publication contains articles that deal with field and laboratory measurements of engineering properties of stiff (overconsolidated) clays, and comparisons of predicted and measured...
Pressuremeter and Foundation Design
The design of shallow and deep foundations on the basis of pressuremeter results is analyzed using numerous load tests and case histories. The foundations are shallow footings subjected...
In-Situ Testing of Peat
It is often economical therefore to start geotechnical investigations with a study of maps and serial photographs and to continue with a detailed program of field reconnaissance. Standard...
Reliability of Pile Capacity Assessment by CPT in Overconsolidated Clay
Correlations for unit skin friction and end bearing are established between cone penetration test (CPT) records, triaxial data and a small data base of measured skin friction and end bearing...
Use of SPT and CPT Tests for Evaluating the Liquefaction Resistance of Sands
A cone penetration test (CPT)-liquefaction resistance relationship has been established using the large body of standard penetration test (SPT) data. Factors for relating CPT tip resistance...
Predictions of Pile Shaft Capacity With the PLS Cell
In situ measurements of stresses and pore pressures on a model pile shaft, the Piezo-Lateral Stress (PLS) cell, are utilized to reconstruct the conditions of load tests involving two large...
Probabilistic Study of SPT Liquefaction Analysis
The influence of earthquake magnitude upon the commonly used correlation between Standard Penetration Test (SPT) blow count and liquefaction potential is evaluated using a probabilistic...
Laboratory and Field Evaluation of Cone Penetrometers
Cone penetrometers from 8 organizations have been studied by performing laboratory tests and field tests. The testing show that pore pressure and temperature zero shift affect significantly...
The DMT - ?hc Method for Piles Driven in Clay
This paper presents a tentative method for evaluating the limiting skin friction f//s for piles driven in clay based on sigma //h'c (horizontal effective stress at the interface...
Determining Sand Strength by Cone Penetrometer
Evaluation has been made of several theories and methods for deducing sand strength from cone resistance. Bearing capacity theories, cavity expansion theory, and empirical methods have...
Measurement of Vertical Ground Vibrations
This paper examines the use of surface and embedded mountings, to which transducers are attached for the measurement of free field vertical ground vibrations. Upper limits to the frequency...
Soil Improvement Evaluation by CPT for Tanks
Trial soil improvement by gravel compaction piles and dynamic consolidation, and a subsequent full-scale loading test on loose volcanic ash soil were conducted prior to the design of large...
Effect of Cementation on the Cone Penetration Resistance of Sand
A laboratory study was conducted to investigate the effect of cementation on the cone penetration resistance of sand. A new apparatus to form homogeneous artificially cemented sand specimens...
Design Parameters for Grouted Piles in Rock From In-Situ Load Tests
A series of pile load tests were performed at an onshore site to develop final geotechnical parameters for the Gaviota platform foundation which consists of large diameter drilled and...
Bearing Capacity of Footings on Clay CPT Method
A method is proposed to predict the ultimate bearing pressure for footings on clay using data from cone penetration tests. This method relates the ratio of ultimate soil bearing for a...
Skin Friction Evaluated From Friction Meter Test
This paper first describes the features of a specially developed friction meter and its operation method, and then reports in-situ test results conducted on various types of soils at two...
Return to search