Use of Geogrids on Soft Deposits
The construction of highway embankments over soft and waste deposits required the use of geogrids as an economical alternate to conventional methods of 'remove and replace'....
Parameter Study of Stresses in Mass Concrete Using Two Fly Ash Mixtures
Finite-element modeling of the incremental construction procedure for mass concrete structures has been used to study the effects of three mechanical properties on thermal stresses. Material...
Concepts for Hybrid FRP Bridge Deck Systems
This paper presents selected structural concepts for modular bridge deck systems taking into account the limitations imposed by fabrication processes for polymer matrix composites. An...
Drying and Shrinkage of Concrete: The Case of Massive Parts
The natural drying of concrete induces a number of intense mechanical effects on the structures. These various effects are of importance to engineers: in the design stage (estimate of...
Significance of Yield Surface Corner-Like Effects in Inelastic Stability Solutions
This paper presents the author's experiences with finite element prediction of the inelastic stability of steel plate structures. The implications of linear versus nonlinear...
On the Road to Clean Air
Anticipating passage of the 1990 Clean Air Act in the fall of the year, this article examines the remaining air quality problems in U.S. cities and some efforts underway or being planned...
Siphon Quenches Drought
An age-old engineering concept�the siphon�enjoys new success in alleviating a severe water shortage at the Ketchikan Pulp Company's Ward Cove Pulp Mill. With major layoffs...
U.S. Landmarks: Handle With Care
Landmarks are treated with kid gloves during restoration, but striking a balance between costs and aesthetics is difficult. In addition to structural integrity, original construction methods...
Ocean Energy Recovery
This proceeding of the International Conference on Ocean Energy Recovery held in Honolulu, Hawaii from November 28-30, 1989 consists of thirty-eight papers. These papers explore various...
Cleaning Up Coal
Coal, which fueled the industrial revolution in the 19th century and two wars in the 20th, should continue to be a major power source well into the 21st century. Its abundance keeps the...
Desktop Publishing for the Design Firm
Desktop publishing lets engineering firms put together reports with high-quality text and graphics in-house. Presentations and publications can be produced with greater flexibility at...
Risk-Based Decision Making in Water Resources
This proceedings represents an edited selection of papers presented at the Engineering Foundation Conference on Risk-Based Decision Making in Water Resources, held in Santa Barbara, California...
Fired Up at Fort Drum
The U.S. Army's first major privatization contract was signed for design, construction, operation and ownership of the Fort Drum powerplant at the newly constructed base for...
Cables and Flexible Pipes in Contact with Sea Floor
Flexible offshore systems can be analyzed by a number of different techniques. The techniques described herein fall in the general category of finite element methods. Special cable elements...
Stability of Plates Under Eccentric Edge Loads
A linear finite element analysis was conducted to study the stress distribution in the web and the flange when the beam is subjected to a patch load applied in the plane of the web or...
Buckling of Unsymmetrical Thin-Walled Members
The formulation of a three-dimensional model based on p-version finite element method for the elastic buckling analysis of unsymmetrical thin-walled members under axial compression and...
Automated Load Capacity Determination of Cold-Formed Steel Compression Members
This paper presents an automated approach for the evaluation of the axial load capacity of nine cold-formed steel sections according to the latest AISI-1986 Cold-Formed Steel Specification....
End Plate Moment Connections for Cyclic Loads
Three pilot tests of full size end plate moment connections under cyclic loading are discussed. In one of the specimens, the premature fracture of one of the inner bolts suggests the possibility...
Strength of Biaxially Crooked Jumbo Columns
The ultimate strength of axially loaded jumbo columns with biaxial initial out-of-straightnesses is analyzed by the finite element method. The analysis makes use of the measured residual...
Evaluation of the Rotation Capacity of Wide-Flange Beams Using Shell Finite Elements
Numerical simulation can be useful for planning of experimental tests, performance of parametric studies, and achieving an understanding of complex three-dimensional behavior that may...
Return to search