Instability of Slopes with Nonassociated Flow
Experimental investigations of the conditions for instability have shown that granular materials may become unstable inside the failure surface. For states of stress below the failure...
Analysis of Internal Discontinuities in Geo-Materials
A new approach for modeling localized deformations is proposed. This approach uses an interface element to model the shear band. A successful capture of the kinematics of a failure mechanism...
Computerized Tomographic Analysis of Fluid Flow in Fractured Tuff
The purpose of this summary is to demonstrate the usefulness of X-ray computerized tomography to observe fluid flow down a fracture and rock matrix inhibition in a sample of Bandelier...
Multiple Modes of Steady-State Slide-Rock Response
The dynamic response of free standing rigid bodies to base excitation can be quite complex, as evidenced by the five motions or modes to be considered in a two-dimensional analysis: rest,...
Dynamic Analysis of Sliding Seismic Isolators
The friction pendulum system (FPS) sliding seismic isolators are being used for the seismic isolation rehabilitation of the U.S. Court of Appeals Building, San Fransisco. This paper will...
The Initiation of Bifurcations and Localization in Damaging Materials
Criteria for diffuse and discontinuous bifurcations have previously been developed and used to investigate the initiation of necking and localization in elastic-plastic materials. In this...
Basic Aspects of Damage Mesomodelling
The basic aspects of a general damage computational approach which enable to simulate the complete fracture phenomenon are presented. It is a semi-discrete modelling where the material,...
Flow Visualization of Lid-Driven Cylindrical Cavity Flow
The lid-driven cylindrical cavity flows in the laminar region are quantitatively visualized by a new flow visualization method called the digital vector velocimetry method. Particle streak...
Three-Dimensional Fracture Process Zone Detection in Concrete
Process zones in concrete have been under intensive investigations during the past several years. Techniques have successfully been used to detect and map the 2-D superficial process zone....
Detection of Cracks in Reinforced Concrete Cans
The Acoustic Emission Technique (AET) is known as a good possibility for non destructive detection of cracks in metal down to very small dimensions. To use AET for concrete, an efficient...
Neural Network Modeling of the Mechanical Behavior of Sand
Given a set of triaxial test data, an artificial neural network (ANN) has been trained to model the mechanical behavior of a medium-to-fine sand. Once trained, the ANN was tested by simulating...
Improved Time-History Analysis for Structural Dynamics Calculations
Methods are developed to reduce the computational effort in time-history analysis of nonlinear structures. The methods permit use of much larger time intervals than are possible in conventional...
Modal Coupling Effect of Non-Classically Damping
The equations of motion of a structure in undamped modal coordinates may have non-zero off-diagonal terms in the damping matrix. Although these terms are commonly neglected, studies have...
Nonlinear Dynamic Response of Framed Structures Using the Mode Superposition Method
This paper describes a methodology for nonlinear dynamic response analysis of framed structures using the mode superposition method. A portal frame example is presented and compared to...
Free Vibration Analysis of Asymmetric Buildings
A simple procedure for free vibration analysis of asymmetric buildings is presented. This method assumes that each floor is a rigid diaphragm with three degrees of freedom (two lateral...
Wave Induced Vortex Near Seashore
The vortex motion behind submerged breakwaters in the nearshore region is studied. The RCPWAVE model (Ebersole et al., 1986) is used to calculate the wave field and thus the radiator stresses...
On the Modelling of Damage Due to Volumic Variations in Cementitious Composites
Two kinds of volumic variations are considered. Those due to thermal gradients on hardened concrete and those due to hydration processes at early ages. Models based on damage mechanics...
Nonlinear Analysis of Strain-Softening Damage under Monotonic and Cyclic Loading
The paper reviews the modeling of damage by the microplane model and presents extensions required for cyclic loading. The general microplane constitutive model is implemented in a three-dimensional...
Dugdale Model Applied to Crack Interactions
It is doubtful that modelling crack interactions problem within the context of elasticity adequately reflects the physical aspects as the failure of brittle material is approached. A model...
Contact Induced Damage
Contact induced damage is an important source of potential failure of engineering components. The particular applications where this damage occurs are in the automotive, aerospace and...
Return to search