New Canadian Provisions Related to the Design of Composite Beams
In this paper, the new provisions in CAN/CSA-S16.1-M89 for the design of composite beams, together with reasons for changes, are discussed. Some of the new provisions reflect results of...
Shear Connection in Composite Beams
This paper considers the influence of the shape of the deck profile on the shear connection of composite beams. It was found that the existing strength reduction factor can be unconservative...
Modern Design Concept for Composite Slabs with Ductile Behaviour
Numerous tests with different types of composite slabs have been carried out in the laboratory for constructional engineering of the University of Kaiserslautern, Germany in order to determine...
Design of Shear Connectors in Composite Bridge Beams
A new approach is described for the design of stud shear connectors, in composite steel and concrete beams that are subjected to vehicular loads, which allows for the interaction between...
Design of Composite Slabs for Vertical Shear
Three major modes of failure should be considered in the design of the positive moment regions of composite slabs incorporating profiled steel sheeting, viz.: flexure, longitudinal slip...
Composite Columns Subjected to Bending and Shear
This paper describes experimental as well as analytical studies of the post elastic deformation and fracture behaviors of wide flange steel encased reinforced concrete (SRC) composite...
Steel Beams with Reinforced Concrete Stiffened Ends
For the construction of office building with long span beams, steel beams with reinforced concrete stiffened ends are being used in order to increase the stiffness. This paper describes...
Behavior of Concrete-Filled Steel Tubular Three-Dimensional Subassemblages
Three-dimensional subassemblages consisting of a concrete-filled steel tubular column and four H-shaped beams were tested under a constant axial load on the column, constant beam loads...
Composite Beams with Headed Studs in Narrow Ribbed Metal Deck
This paper presents the results of sixteen push-out tests conducted to study the behavior of headed stud connectors in composite beams with narrow ribbed metal deck placed parallel to...
Steel Panel Encased R.C. Composite Shear Walls
In order to make clear the fundamental resisting mechanisms of composite shear walls, tests are carried out on the composite unit rigid frames with various infilled shear walls. Composite...
The Behaviour of Reinforced Concrete Beams Manufactured with Side Profile Sheets
The paper describes in qualitative terms the fundamental principles that control the behaviour of a completely new form of construction in which reinforced concrete beams are constructed...
SHRP Deformation Test?Asphalt Mix Tests and Analysis Systems
From analyses of existing information on the permanent-deformation characteristics of asphalt/binder-aggregate mixes, as well as the development of permanent deformation in pavement structures,...
Generic Problems
Generic Problems are basic problems in structural mechanics that recur frequently, have been investigated experimentally and involve the behavior of elements or components found in many...
Seismic Design of Multi-Story, Wood-Framed Buildings
The seismic design and analysis of wood-framed structures is relatively simple; however, the challenges that present themselves within this design medium are shear and overturning force...
Damage Dependent Micromechanics in Metal Matrix Composites
A computational approach is used herein to model the effects of processing induced thermal residual stresses on radial, hoop, and shear stresses at the fiber/matrix interface in a continuous...
Soil Behavior from Unconventional Loading Conditions
Random and sinusoidal loading conditions were used in this study to determine the soil moduli and the damping ratios of cohesive soil samples. Test results showed some differences between...
Relationships Between Error Estimation and Adaptive Computations in Strain Localization
In this work, the a posteriori error estimates and the h mesh refinement techniques using hierarchical finite element shape functions are tailored for numerical simulations of strain localization...
Analysis of Internal Discontinuities in Geo-Materials
A new approach for modeling localized deformations is proposed. This approach uses an interface element to model the shear band. A successful capture of the kinematics of a failure mechanism...
Computer Simulation of Direct Shear Test
This paper presents a pilot study of a computer simulation of direct shear test on sands using the Discrete Element Method. The numerical test setup is described first, which is followed...
A Shear Locking Free Three-Node Triangular Plate Bending Element for Moderately-Thick and Thin Symmetrically Cross-Ply Laminated Plates
A shear locking free three-node triangular plate bending element based on Reissner/Mindlin theory for symmetric general cross-ply laminated plates is developed. The element has total nine...
Return to search