Computer-Aided Load Monitoring System for Nuclear Power Plant Steel Framing Structures
The design of nuclear power plant steel framing structures is a long and involved process. It is often complicated by numerous changes in design loads as a result of additions, deletions...
Probabilistic Seismic Analysis of a Nuclear Power Plant Steel Containment
Concern for the safety of nuclear power plants has motivated efforts to determine the statistical characteristics of the seismic resistance of steel containments under various types of...
The Response of Steel Containment Models to Internal Pressurization
To obtain insight and data on the response of containment vessels subjected to beyond design basis accidents, four 1/32 scale steel containment models have been subjected to internal overpressurization,...
Tension Tests of Containment Wall Isolated Liner Plates
Two tests were conducted using an approximate 2:1 ratio of hoop to meridional load. This simple load ratio is a gross approximation of the liner plate loading in a containment subjected...
Containment Integrity of SEP Plants under Combined Loads
The containment designs analyzed consisted of three inverted light-bulb shaped drywells used in boiling water reactor (BWR) systems, and three steel-lines concrete containments and a spherical...
Determination of Containment Vessel Ultimate Capacity Using Nonlinear Finite Element Analysis
Analysis of steel containment vessels is normally performed using linear elastic solutions with allowable stresses specified by applicable design codes. This method gives little indication...
Structural Performance Predictions for Liner Plates on Nuclear Facilities
The history of the use of liner plates is presented. It is shown that the liner plate can be buckled, and can be bonded or not bonded to the concrete. The buckled plate usually has bending...
Simplified Design of Flexible Expansion Anchored Plates for Nuclear Structures
The following two phases of the design of expansion anchored plates are discussed in this paper. a) Initial Design. b) Reassessment of as-built conditions. Initial design refers to the...
ACI 349 Embedments: Code Provisions and Methods of Analysis
Steel embedments form the critical link between steel and concrete structures. Appendix B of ACT 349, Code Requirements for Nuclear Safety Related Concrete Structures, specifies the ultimate...
State-of-the-Art Report on Steel Embedments
The basic philosophy underlying the design of steel embedments may be summarized as follows: (1) If an attachment can be located such that a group of cast-in-place anchors can be used...
Importance of Pipe Soil Stiffness Ratio in Plastic Pipe Design
In this paper, the finite element method of analysis is used to study the effect of pipe-soil stiffness ratio on axial forces, bending moments, and deflection of pipes of varying stiffness....
The Present Status of Application of the Plastic Concepts in Structural Design
The different approaches of recognizing plastic behavior in the design of steel structures are reviewed and the design requirements that assure successful utilization of this behavior...
Computer-Automated Limit-States-Design of Steel Frameworks
The paper concerns the computer-automated synthesis of minimum-weight planar steel frameworks. For any number of applied loading cases, the design of the structure may be constrained by...
Limit State Analysis of Lattice Steel Transmission Towers
The background and present status for limit state analysis of lattice steel towers at the Bonneville Power Administration is presented. Conceptual development, a computer program, and...
Reliability-Based LRFD for Transmission Structures
A simple reliability-based Load and Resistance Factor Design (LRFD) method is proposed for the structural design of electric transmission lines. With the proposed method, the designer...
Pile Caps Subjected to Lateral Loads
This paper reviews current pile cap design practices and presents results of tests on two pile caps with different reinforcement locations. Lateral load tests performed on two pile cap...
Advanced Graphical CAD System for 3D Steel Frames
An innovative, advanced graphical computer-aided design system, called STEEL-3D, is described. The main objective of this program is to provide the engineer with all the tools necessary...
Influence of Connection Behavior on Steel Frame Designs at Factored Loads
This paper illustrates how interactive computer graphics, when interfaced with nonlinear inelastic frame analysis programs, can provide a powerful tool for design of semi-rigid frames...
Hydrotest Rupture of Penstuck Liner at Bath County
Bath County is the construction site of Virginia Electric and Power Company's pumped storage project. Rupture of a penstock liner during hydrotest at high pressure threatened...
Computer Aided Design in Civil Engineering
Increased application of computer aided design and drafting encouraged the organization of the symposium from which this book was derived. The papers presented at the symposium and included...
Return to search