ASCE will be sunsetting the Civil Engineering Database (CEDB) in the coming months. We encourage you to start using the ASCE Library to perform content searches. In the ASCE Library, you can save your search results as well as receive email content alerts when new content relevant to your area of interest is published. Try it out today at https://ascelibrary.org.

 

Performance and Analysis of Frames With URM Infills
The interaction of unreinforced hollow concrete block masonry (URM) infill walls and gravity load designed (GLD) frames has been studied at Cornell University. The primary goal of this...

Behaviour of Concrete Masonry Infill - Steel Frame Structures
Twenty-eight masonry shear panels infilled in steel frames were tested to ultimate strength under in-plane, horizontal loading applied at roof level. The parameters investigated in this...

Lateral Response of Unreinforced Masonry Infill Frame Panels
This paper presents the results of the out-of-plane testing phase of the National Science Foundation Grant BCS 9102347. This project addresses the out-of-plane response to lateral loading...

Experimental Evaluation and Finite Element Analysis of Masonry-Infilled R/C Frames
Eleven tests were conducted on 1/2-scale, single-story infilled frame specimens to study the influence of the relative strengths of the infill panels and the bounding frames and the frame...

Damage Tolerance Analysis in Structural Rehabilitation
The rehabilitation of existing structures requires an evaluation by the structural engineer of past performance to determine the extent of existing damage. Following evaluation of the...

How to Optimize Light-Gage, Cold-Formed Steel Beams
The Illustrative Examples section of the AISI Cold-Formed Steel Design Manual (AISI 1989) demonstrates how to analyze a number of different cold-formed steel sections. This paper applies...

Optimization for Earthquake Loads
Structural optimization for seismic loads can be approached from a deterministic or nondeterministic point of view. Deterministically, the major difference between optimization of statically...

Structural Analysis for Structural Design
This paper presents a simple extension to conventional structural analysis that serves to provide additional information that is of significant use to the structural design process. Specifically,...

Distributed Flexibility Models for Nonlinear Analysis of RC Structures
The application of distributed flexibility member models in inelastic analysis of reinforced concrete (RC) structural systems is examined. While the utilization of flexibility-based formulations...

RC Beam-Column Element for Nonlinear Frame Analysis
Recent studies have shown that beam-column finite elements that enforce equilibrium rather than compatibility along the element are better suited for the description of the strength and...

Applicability of Pseudo-force method to Highly Nonlinear Dynamic Problems
This paper deals with solution of nonlinear dynamic problems using Pseudo-force method. A solution algorithm involving Pseudo-force method is presented. The objective is to investigate...

Large-Scale Computations in Analysis of Structures
Computer hardware and numerical analysis algorithms have progressed to a point where many engineering organizations and universities can perform nonlinear analyses on a routine basis....

An Automated Environment for Parallel Computing
Research on a prototype concurrent software development environment for large-scale structural engineering computing is currently underway at Purdue University. This environment is being...

Timing Analysis of a Multiprocessor Architecture for Active Control
This paper describes how real-time multiprocessor systems, such as those required for active structural control, can be developed to satisfy timing requirements on hardware and software....

Flange Local Buckling and Behavior of I-Sections
A simple kinematic model is proposed to determine the locally buckled shape of the compressive flange plate of I-sections subjected to pure bending or bending combined with axial thrust....

Finite Element Analysis of Shear in RC Girders
Two complementary approaches are presented to model the shear behaviour of reinforced concrete structures. A local one, based on a probabilistic modelling of cracking, accounts for local...

Computer-Aided Structural Engineering Software: The Status of Concurrent Engineering
Concurrent engineering encompasses computer-aided engineering (CAE), multidisciplinary CAE (MCAE), computer-aided design and drafting (CADD), computer-aided manufacturing (CAM), computer...

Application of Computer-Aided Structural Engineering
From as early as 1988, the Civil/Structural Group of Bechtel Corp.'s Houston Regional Office has viewed its automated production tools as components of a production system. Intergraph's...

Checking of CAD Drawings for Fabrication Issues
Communication between the fabricator and engineer is crucial to the production of an economical, safe, and functional steel structure. However, the transfer of information between involved...

Steel Detailing Neutral File from Modeling Software
Today's generation of computer graphics applications used for the purposes of modeling industrial structures can now transmit engineering electronic data to other downstream functions....

 

 

 

 

Return to search