Analytical Model for RC Panels Under Cyclic Load
There are several existing constitutive laws for cracked concrete and steel in RC developed in Okamura laboratory. These models have been developed and verified through reversed uniaxial...
Development of Analytical Models for Reinforced Concrete
A computer program called WCOMR was developed to analyze the characteristics of RC walls subjected to reversed cyclic loading. The WCOMR comprises RC element idealization described by...
Wood Diaphragms: Performance Requirements and Analytical Modeling
Wood diaphragms represent the principal mechanisms for resisting lateral loads in many light-frame buildings. While recent research has provided several mathematical models for predicting...
Lateral Force Distribution in Manufactured Housing from Full-Scale Testing
The research focused on the behavior of two manufactured 14 ? 66 ft houses under simulated wind loads. Extensive instrumentation was employed to insure the collection of data that would...
Forces in Unbonded Tendons
A rational analysis procedure for the calculation of tendon forces in prestressed beams with unbonded tendons is discussed. The prestressing tendon is analyzed as a tight-string which...
Analysis of Slender Prestressed Concrete Columns
This paper briefly describes an analytical model developed to study slenderness effects in prestressed concrete columns and walls and predict the characteristics of such members over a...
Parametric Analyses of RC Shear Walls by FEM
In this paper, nonlinear behavior of reinforced concrete shear walls is studied by using the finite element analysis. We applied numerical analyses to a wide range of parameters, such...
LRFD for U. S. Bridge Design ? Validation Issues
During the 1987 meeting of the AASHTO Subcommittee on Bridges and Structures, recommendations from the National Cooperative Highway Research Program (NCHRP), Project 20-7/31, regarding...
Reliability-Based Design of Transmission Line Structures
Reliability-Based Design (RBD) is an emerging concept for the design of transmission line structures and holds the potential to reduce the cost of lines or increase their reliability....
Strength Evaluation of Existing Reinforced Concrete Structures
The load test as described in ACI 318-83 Chapter 20, entitled 'Strength Evaluation of Existing Structures,' was conducted at 60%, 80%, and 100% of the calculated...
Fourier Series Expansion on Determination of Response Bound of Beam
Fourier series expansion is suggested to discrete the continuous vibrating system by regarding Fourier constants as generalized displacement parameters. The orthogonal merit to the terms...
Dynamic Response of a Building with Dual System
The paper presents the dynamic response of a 30-story building with dual system consisting of cross-bracing and beam-column moment resisting frames. Two types of beam-column connections,...
Wind Performance of Asphalt Roofing Shingles
Pre-seal and post-seal wind resistance of asphalt roofing shingles is discussed. A test method for evaluating pre-seal wind damage is described. Wind tunnel testing results are presented...
A New Proposal of Design Wind Loads for Beams Supporting Long-Span Roofs
The wind tunnel testings of wind pressures acting on long-span roofs are carried out. Dynamic wind pressures are measured simultaneously at a lot of points on the roofs. The instantaneous...
Toward an LRFD-Based AASHTO Bridge Specification
During the 1987 AASHTO Bridge Committee Meeting, recommendations from NCHRP Project 20-7/31 regarding the development of a probability-based LRFD bridge specification were accepted. NCHRP...
Bridge Loading Evaluation for Limit States Design in Japan
Some statistics regarding bridges in Japan are firstly explained. Next, the limit states design which will be introduced in 1995 for highway bridge design specification in Japan is briefly...
Evaluation of Bridge Safety and Remaining Life
In developed countries, the emphasis on the infrastructure is changing from new construction to the safe maintenance of existing structures. Highway bridges represent an excellent example...
Load and Resistance Factor Design for Engineered Wood Construction
The wood industry has provided sponsorship for the development of a reliability-based, load and resistance factor design specification for engineered wood structures. This user-tested,...
Load Combinations for LRFD With Wood Construction
Probability based limit states design for wood construction is complicated by the fact that wood is a natural material with large variations in mechanical properties and is sensitive to...
LRFD for Engineered Wood Construction: Calibration to Current Design
The structural design code for engineered wood construction is evolving to a limit state design basis in which the safety checks are derived from the underlying probability distributions...
Return to search