Riprap Stability in Channel Bends
A systematic test series is underway in a large test channel to define the stability of riprap on the outer bank of channel bends. A 'practical equilibrium' concept...
The Effects of Bank Protection on River Morphology
Revetment of bends with radius of curvature to width ratios (R/W) between 1.9 and 3.3 on Red River AR, and Sacramento River CA, does not cause the expected thalweg deepening and channel...
Numerical Model Studies of Wetland Hydraulics for Bolsa Bay, California
The Bolsa Bay area, near Los Angeles, presently consists of three distinct regions separated by two sets of culverts. A development is being considered, in which a balance between housing...
Numerical Modeling of Hydraulic Jump
Boussinesq equations describing one-dimensional unsteady, rapidly varied flows are numerically integrated by using a second-order and a fourth-order accurate explicit finite-difference...
General Formulation of Best Hydraulic Channel Section
The best hydraulic channel section is determined by using Lagrange's method of undetermined multipliers. The approach presented is more general & easier to apply than...
Control of Bank Erosion in The Netherlands. State-of-the-art
In the Netherlands the protection against flooding and the effects of inland navigation have always been extremely important. Many problems related to these items, among them erosion and...
Performance Characteristics of Compound Weirs
A theory is outlined which helps to explain the flow over compound weir under free overfall conditions. Experiments on twelve weirs of three sets with different dimensions are shown to...
Relief of an Urban Storm Drainage System
The Peaks Branch storm sewer system was designed in the 1930s to drain 5.7 square miles of East Dallas. Subsequently, development blocked the emergency overflow paths and many areas are...
Closed Conduit Vapor Lock
Closed conduit vapor lock can occur when a cross country liquid pipeline is displaced with a gas and the gas is allowed to get ahead of the liquid/gas interface. A simple hydraulic model...
Hydraulic Transient Analysis of High-Head Hydropower Project
An iterative computer simulation procedure called LIQT (Liquid Transient), which performs simulations of hydraulic transients in closed conduit hydro-power systems, is used to estimate...
Effects of Vegetation on Floods at Four Arizona Sites
Four examples show the effect of vegetation on stage, discharge or frequency of floods. An 8-year growth of trees on the streambed at site 1 increased channel roughness enough to cause...
SWMM Application in Indian River County, Florida
The EPA's Storm Water Management Model (SWMM) was used to simulate drainage canal system network within Indian River County, Florida. Runoff and Extran module of the PCSWMM...
Experience with Cavitation in High Pressure Slide Gates
The Bureau of Reclamation has many years of experience in the design and operation of high pressure slide gates. This paper discusses the historical use of high pressure slide gates by...
Design, Construction and Testing of Repairs to the Low Level Outlets at Terzaghi Dam
Operation of the low level outlets (LLOs) at Terzaghi Dam in southwestern British Columbia resulted in severe cavitation at operating heads significantly lower than design. Modifications...
Design and Operation of Guard Gates
Guard gates for hydroelectric intakes and low-level outlets are normally intended for operation only under balanced heads. In the case of failure of regulating gates, the guard gate may...
Handling of Intake Bulkhead at King Talal Dam
During raising of King Talal Dam in Jordan in 1986, the existing intake wheel gate provided at the inlet of the project Low Level Outlet Works (LLOW) tunnel was found inadequate to withstand...
Model-Prototype Comparison of the Bay Springs Lock, Tennessee-Tombigbee Waterway, Mississippi
A comprehensive prototype evaluation of the Bay Springs Lock, Tennessee-Tombigbee Waterway, Mississippi, was conducted by the Hydraulics Laboratory, Waterways Experiment Station (WES)....
Model Study of New Bonneville Lock
The filling and emptying system of the New Bonneville Lock was designed by the US Army Engineer District, Portland. The lock will be 86 ft wide by 675 ft long, with a design lift of 69.5...
Model Study of Potential Debris Problems at the Proposed Diversion of Clover Fork River, Harlan, Kentucky
A study was conducted at the Waterways Experiment Station in Vicksburg, Mississippi, using a physical and a numerical model, to evaluate the entrance conditions at a proposed tunnel diversion...
Hydraulics of Side-Channel Weirs for Regional Detention Basins
Side-channel weirs can be used for diversion to reduce flood peaks. A 1:25 scale model was built to investigate the hydraulic characteristics of embankment-shaped side-channel weirs. Results...
Return to search