ASCE will be sunsetting the Civil Engineering Database (CEDB) in the coming months. We encourage you to start using the ASCE Library to perform content searches. In the ASCE Library, you can save your search results as well as receive email content alerts when new content relevant to your area of interest is published. Try it out today at https://ascelibrary.org.

 

Sizing Techniques for Lateral Bracing
Techniques for determining the size of lateral bracing members in multi-story steel buildings are presented and discussed. Because the design of such bracing is usually controlled by deflection...

Double Angle Bracing Members
It has been pointed out that when a single line of bracing is used, the member is usually made from structural tubing. It has been suggested that when the loads are not too great, consideration...

Analysis of Tapered and Stepped Columns by Analogy to Cantilever Deflection
An analysis is developed for handling the buckling design of tapered and stepped columns with the aid of the so called 'amplification factors'. When these factors...

Optimum Design of Tapered Tubular Members
An algorithm for designing a tubular structural member with constant taper is presented. The design criterion is that the maximum absolute stress produced by a set of loading conditions...

Buckling Load of Tapered Columns
The basic tapered column with larger section in the center, is considered using Rayleigh-Timoshenko method. Column has linearly increasing I_o with...

Buckling of Variable Cross-Section Columns
An approximate solution for the problem of buckling of variable cross-section columns, loaded by variable axial force is given, for several boundary conditions. Both the cross-section...

Steel Girt Design
Procedures are presented for the design of light gage cold formed girts and hot rolled girts. The effects of continuity, sag rods, and wall sheeting are discussed. Design procedures are...

Cold-Formed Z-Sections Under Axial Load and Bending
The use of cold-formed Z-section members as beam-columns presents some unique design problems which are not adequately addressed in the current design specifications. If these members...

Automated Load Capacity Determination of Cold-Formed Steel Compression Members
This paper presents an automated approach for the evaluation of the axial load capacity of nine cold-formed steel sections according to the latest AISI-1986 Cold-Formed Steel Specification....

Seismic Response of Flexibly-Connected Steel Frames
The response of typical low-rise steel building frames designed by the 'Type 2 Construction' method to moderate earthquakes is examined. Such frames are often...

End Plate Moment Connections for Cyclic Loads
Three pilot tests of full size end plate moment connections under cyclic loading are discussed. In one of the specimens, the premature fracture of one of the inner bolts suggests the possibility...

Strength of Biaxially Crooked Jumbo Columns
The ultimate strength of axially loaded jumbo columns with biaxial initial out-of-straightnesses is analyzed by the finite element method. The analysis makes use of the measured residual...

Stablity Considerations in the New E&CS Building
The new Engineering and Computer Science (E & CS) building at California State University, Sacramento (CSUS) is a five-story structure characterized by two shear walls in the east-west...

Tripping and Strength of Asymmetrical Plate Stiffeners
Tripping (lateral-torsional buckling) of symmetrical or asymmetrical plate stiffeners can be analyzed by using differential equations or energy formulation. An analytical study is reported...

Portal Frame Stability with Nonproportional Loads
An inelastic theoretical study of the effect of various load paths is conducted on the in-plane behavior of an imperfect portal frame with flexible joints. The loading consists of concentrated...

Analysis of the Non-Planar Response of a Cantilever, with the Aid of Computerized Symbolic Manipulation
The nonlinear differential equations governing the static deformations of a cantilever with a tip mass are formulated and analyzed with the aid of computerized symbolic manipulation. The...

Experiments on Active Structural Control Under Seismic Loads
Two control systems, an active tendon system and an active mass damper system are selected for study for possible real structural implementation. Presented in this paper are simulation...

A Comparison of Performances of Various Frictional Base Isolation Systems
The results of a comparative study of the performances of several frictional base isolation devices including the Sliding-Joint, the French System, and the Resilient-Friction isolators...

Frequency Response Design of Controlled Structures
The installation of optimal control systems has been shown to be effective in reducing the vibration responses of structures. In addition to the effectiveness, there are many factors that...

Applications of Fuzzy Mathematical Programming in Structural Optimization
In this paper, several applications of fuzzy mathematical programming in structural optimization are reviewed and discussed. In addition, a formulation of optimum earthquake resistant...

 

 

 

 

Return to search