Simplified Reliability Analysis of Transmission Structures Including Both Geometric and Material Nonlinearities
Generally, in nonlinear structural systems, the g-functions of the components cannot be explicitly expressed in terms of the basic random variables. In using the design point method to...
Causal Probabilistic Networks in Assessing the Vulnerability of Existing Buildings
A probabilistic assessment of the 'state of health' of the structure is pursued on the basis of pieces of evidence collected by inspection and by querying, in case, historical data bases....
A Prototype Expert System for Rapid Visual Screening of Seismically Hazardous Buildings in California
A rapid visual screening expert system, California Rapid Building Seismic Evaluation Expert, was developed to enable efficient and effective identification of seismically hazardous buildings...
Fatigue Reliability of Structural Systems Under Earthquake Loads
The authors have develop a methodology for calculating the expected low-cycle fatigue damage in structural components subjected to brief nonstationary random loads. The methodology is...
The Effect of Nonlinear Drag PSD on Fatigue of Compliant Offshore Structures
Structural fatigue damage induced by random ocean wave loading on a compliant type of offshore structure is considered. The nonlinear wave force is modeled by the Morison equation and...
Fatigue of Floating Offshore Structures: Modelling Uncertainty in Hydrodynamics and Fatigue Properties
For floating offshore structures such as tension leg platforms (TLPs), one form of loading uncertainty is due to nonlinear diffraction forces, which can excite lightly damped vertical...
Time Variant Reliability Under Environmental Loads
Time variant reliability with deteriorating resistance under a stochastic load process is considered. An outcrossing formulation for fatigue degradation is presented, and a simple and...
Durability and Ductility of Advanced Composites
In recent years, several fiber reinforced composites have been successfully used as prestressing materials for demonstration highway structures. Since these materials are relatively brittle...
A Model Specification for Pultruded Structural Shapes: An Industry Collaborative
The use of pultruded products is steadily increasing. To support this growth, the industry has identified the need for a collaborative effort in developing standards that form a base line...
Flexural and Shear Behavior of Combined Concrete and Graphite Epoxy Beams
An experimental and analytical study of six graphite composite beams are presented. Four of the beams incorporated a reinforced concrete slab. The composite action and the effect of concrete...
Design Optimization of an All-FRP Short-Span Bridge
The objectives of this study are: a) to determine the feasibility of designing an all-FRP bridge, and b) to demonstrate the usefulness of optimization techniques in the design of FRP superstructures....
Steel Fiber Reinforcement in Structural Application
Ribbon Technology Corporation's use of steel fiber reinforced concrete in the construction of their new manufacturing and office facility in Gahanna, Ohio. Cost savings are obtained by...
Strength, Behavior and Repair of Masonry Infills
Results of a series of experiments are presented on seismic performance of unreinforced masonry infill panels. The object of the investigation is to examine the loss of out-of-plane strength...
The Use of Built-Up Compression Members?A Fabricator's Viewpoint
A variety of cross-sections of built-up compression members that have been used are shown. Suggested items that need to be addressed for the successful design and fabrication are discussed....
Built-Up Compression Members for Noval Structural Systems
This paper discusses built-up compression members used in novel structural systems for two high-rise buildings: InterFirst Plaza at Dallas Main Center and Columbus Center in New York....
QST Rolled Shapes, a New Generation of HSLA Compression Members
With the development of the Quenching and Self-Tempering (QST) process by the Luxembourg steelmaker ARBED S.A., a new generation of High Strength Low Alloy (HSLA) rolled shapes has become...
Creep and Shrinkage of Composite Columns in Tall Buildings
The simultaneous presence of steel and composite columns in tall buildings is a common occurrence. The axial shortening characteristics of composite columns are influenced by creep and...
Achieving Level Composite Steel Floors
Constructing deflected composite steel floors that are level is a complex operation, and one which requires cooperation and an exchange of information between the structural engineer and...
Field Measurements of Wind-Induced Pressures on Roofs of Low Buildings
Full-scale measurements have been carried out on an experimental building, 3.3 m high, beside the football field at the Loyola campus of Concordia University. Wind-induced pressures have...
Steel Bar Joist Performance: Design Deficiencies and Defects
Several failures of steel bar joist roofs have been investigated by the authors in the past decade. Many of these failures or performance problems have corresponded to bar joists manufactured...
Return to search