Seismic Resistance of Steel Fiber Reinforced Concrete Beam-Column Joints
This paper discusses the advantages of using steel fibers in seismic resistant beam-column connections. First, the effects of fibers on the various aspects of behavior of concrete are...
Analysis and Design of SFRC Structural Elements
This paper presents and validates practical methods for flexural, shear and torsional analysis and design of fibrous reinforced concrete structural elements. The effects of both fiber...
Steel Fiber Reinforcement in Structural Application
Ribbon Technology Corporation's use of steel fiber reinforced concrete in the construction of their new manufacturing and office facility in Gahanna, Ohio. Cost savings are obtained by...
The Use of Built-Up Compression Members?A Fabricator's Viewpoint
A variety of cross-sections of built-up compression members that have been used are shown. Suggested items that need to be addressed for the successful design and fabrication are discussed....
Built-Up Compression Members for Noval Structural Systems
This paper discusses built-up compression members used in novel structural systems for two high-rise buildings: InterFirst Plaza at Dallas Main Center and Columbus Center in New York....
Design of Built Up Compression Members for Long Span Bridge Structures
This paper discusses the design of built up compression members for long span bridge structures including trusses and arches. Provisions of load factor design and use of high strength...
A New Theory of Built-Up Columns
In laced, battened and other built up columns the shear stiffness of the web can have a significant effect on the overall buckling load. At the present time, such columns are analyzed...
QST Rolled Shapes, a New Generation of HSLA Compression Members
With the development of the Quenching and Self-Tempering (QST) process by the Luxembourg steelmaker ARBED S.A., a new generation of High Strength Low Alloy (HSLA) rolled shapes has become...
Creep and Shrinkage of Composite Columns in Tall Buildings
The simultaneous presence of steel and composite columns in tall buildings is a common occurrence. The axial shortening characteristics of composite columns are influenced by creep and...
Performance and Serviceability of Composite Floors
Concrete slabs on steel deck are the most common type of floor system in use today. This system of construction is particularly advantageous when ultimate strength design (LRFD) is used....
Achieving Level Composite Steel Floors
Constructing deflected composite steel floors that are level is a complex operation, and one which requires cooperation and an exchange of information between the structural engineer and...
Vibration and Impact in Skewed Steel Bridges
The vibration and impact of skewed multigirder bridges due to vehicles moving across rough bridge deck are studied. The bridges are modeled as grillage beam systems. The vehicle is simulated...
Ambient Vibration Response of a Long Span Bridge
Natural frequencies, mode shapes and damping characteristics for a long-span cable-stayed bridge were experimentally determined from a series of ambient vibration tests for both the cantilever...
Magnetic Flux Leakage for Bridge Inspection
For many years the Federal Highway Administration and before that the Bureau of Public Roads had focused its nondestructive evaluation program on development of better tools to inspect...
Remote Monitoring of a Stressed Timber Bridge Deck
The long term behavior of a CCA treated stressed timber deck bridge is being monitored, at present, using a remote data acquisition system. The bridge which is located in Gray, Maine was...
Full Scale Dynamic Monitoring of Highway Bridges
Sensitivity of identified modal properties by physical testing is critical for automated monitoring of bridge structural condition. It is investigated here considering flexure modes and...
What is Optimization?
Basic concepts of optimization are described using design of a plate girder as an example. First, a way to formulate the problem as an optimization problem is presented. Then basic terminologies...
How to Optimize Steel Frameworks
This paper presents the details of a design synthesis strategy to conduct computer-automated design of least-weight structural steel frameworks, where members are automatically sized using...
Structural Analysis in Context
The issues of what student should learn about structural analysis and how it should be taught are explored considering the purposes of structural analysis in engineering practice and the...
Construction of CCM Overtopping Protection on Three Parkway Dams
Cellular concrete mat (CCM) systems have been installed as overtopping protection on three small embankment dams along the Blue Ridge Parkway. Based on field tests by others and on the...
Return to search