Seismic Safety Modification of an Old Earthfill Dam
Chollas Dam was built as a water supply reservoir for the City of San Diego. The reservoir is no longer a part of the municipal water system but has been operated since 1966 as a recreational...

Geometric Design Projects for Highways
An Introduction
This book provides an introduction to geometric design of highways by means of examaples and projects that emphasize basic specifications, approaches to preliminary route selection, alignment,...

Application of Monte Carlo Neutron Photon to Hanford Waste Vitrification Plant Design Analysis
The Monte Carlo Neutron Photon (MCNP) computer program ('MNCP - A General Monte Carlo Code for Neutron and Photon Transport, Version 3A') (in PC and mainframe versions) has been used for...

Installation and Routing of Critical Embedments at the Hanford Waste Vitrification Plant
During the preliminary design phase of the project, a study was conducted to develop concepts for routing embedded piping and conduit between the remote cells and the service corridors...

Mechanical Design of the Storage Tubes in the HWVP Canister Storage Building
Canisters of high-level waste from the Hanford Waste Vitrification Plant (HWVP) will be stored in an adjacent facility, the Canister Storage Building (CSB). The canisters are stored vertically...

Critical Stresses in Nuclear Waste Container Under Normal Handling Conditions
Critical stresses in the pintle, flat tophead, canister shell, the bottom plate and in the weldment of a high level nuclear waste canister are evaluated under a variety of static and dynamic...

Remote Spent Fuel Handling in France at the La Hague Cask Unloading Facility
French policy for the back end of fuel cycle is based on spent fuel reprocessing. Irradiated spent fuels are transferred in casks from the nuclear reactors to the reprocessing plant where...

Conceptual Design of a Monitored Retrievable Storage Facility
In order to achieve timely acceptance of spent nuclear fuel into the federal radioactive waste management system and to limit the amount of additional at-reactor storage capacity that...

A Systematic Human Factors Assessment of a Department of Energy Facility
This paper presents the methodology for conducting a systematic human factors assessment of the as-built configuration of buildings at the Rocky Flats Plant (RFP). In support of this effort,...

Global Approaches for the Nonconvex Optimization of Pipe Networks
Because the pipe network problem is nonconvex, two global search schemes, MULTISTART and ANNEALING, are employed to permit a local optimum seeking method to migrate among various local...

Identifying the True Issues of Hydropower Resource Development in an Era of Public and Regulatory Policy Transition
The last several years have produced changes in public and regulatory policy that have provided for increased roles and participation of resource agencies, Native Americans, and the public...

Alternatives Analysis Using Two-Dimensional Modeling for the Owensboro Bridge and Approaches
The Federal Highway Administration plans to design and construct a new bridge over the Ohio River near Owensboro Kentucky. A hydraulic model with two-dimensional capabilities was utilized....

Design of Pile Foundations
This handbook, Design of Pile Foundations, provides information on foundation exploration and testing procedures, load test methods, analysis...

Dynamic Analysis and Design Considerations for High-Level Nuclear Waste Repositories
This proceedings, Dynamic Analysis and Design Considerations for High-Level Nuclear Waste Repositories, consists of papers presented at the...

F. E. Everett Turnpike: An Application of MOSS
MOSS surface modeling software is being used successfully by Fay, Spofford & Thorndike, Inc., on a major project for the New Hampshire Department of Transportation to make improvements...

The Application of AI in Highway CAD System
In a conventional CAD System, the process for solving a certain particular engineering problem is fixed stationary in the program. As a result, the program is often modified to fit different...

The 3D Approach to Design
Designing directly in three dimensions, including integrated analysis and information flow, is a powerful way to enhance civil engineering capabilities. Yet, relatively few have taken...

Designing in Three Dimensions for Manufacturing Facilities
Du Pont Engineering is using Three-Dimensional Design for the design of our manufacturing facilities. Our 3D design system was used on several projects in 1992, and full implementation...

Object Oriented Modeling of Structural Systems
Computational engineering in structural design is no longer restricted to numerical approaches. Increasingly, also non-numerical, in particular, cognitive problems can be implemented into...

Object-Oriented Modelling for Concrete Structures
The use of computers for the design process has reached wide acceptance. The use is developed in several fields such as CAD, CAM or programs for design of structural elements. Recent work...

 

 

 

 

Return to search