Over Open Water
Because of environmental considerations, construction of the wharf for the new Paulsboro Marine Terminal, in Paulsboro, New Jersey, could not cause the loss of in-water or intertidal habitat at the site....

When Old Meets New: Railway Geotechnics and Remote Sensing
Railroad track, like any other built structure, relies on a foundation of geomaterials for support. In its most basal form, the railway track is quite simple: steel load-bearing members (rails) supported...

A Pioneering Structure: The Eads Bridge
Though he was not trained as an engineer, James Buchanan Eads had the vision and will to design one of the great bridges of the 19th century. The Eads Bridge, spanning the Mississippi River at St. Louis,...

Spread Footings Revisited: Geotechnical Advances Lead to Expanded Use for Bridge Abutments
The Minnesota Department of Transportation (MnDOT) has historically used steel shell piles to support highway bridge structures, probably due to a blend of familiarity and efficiency among...

Screw Piles and Helical Anchors: 180 Years of Use in Geotechnical Engineering
Since 1836, screw piles and screw cylinders have been used successfully throughout the world to support a variety of large-scale, civil engineering structures. Their development and use...

Long-Term Performance Monitoring of a Hillside Retaining Wall
To accommodate expansion of the West Point Treatment Plant in Seattle, WA, a 3,000-ft-long soldier pile, tieback-anchored retaining wall was constructed from May 1991 to May 1992. An oblique...

General
Design of Latticed Steel Transmission Structures specifies requirements for the design, fabrication, and testing of members and connections for electrical transmission structures. These...

Loading, Geometry, and Analysis
This Standard applies to latticed steel transmission structures. These structures shall be either self-supporting or guyed. They consist of hot-rolled or cold-formed prismatic members...

Structural Members and Connections Used in Foundations
This chapter specifies design procedures for steel members and connections embedded in concrete foundations or the earth. Additional design requirements for structural members and connections...

A Simple Model to Predict Soil Resistance to Driving for Long Piles in Deepwater Normally Consolidated Clays
As the exploration and development for offshore oil and gas reserves moves into the deepwater environment of the continental slope, a good model is necessary to evaluate drivability of...

Axial Load Capacity of Pipe Piles in Sands
The axial load capacity of driven, open-ended, steel pipe piles in cohesionless soils, is often estimated using a method such as the American Petroleum Institute Recommended Practice 2A...

Behaviour of Open-Ended Pipe Piles in Sand During Installation and Loading
An experimental study was performed to investigate the physical processes which influence the axial load capacities of open-ended steel pipe piles in sand. A double-walled pipe pile was...

Pile-Driving Formulas for Friction Piles in Sand
Dynamic pile-driving formulas are widely used in predicting the load-carrying capacity of friction piles and in writing pile-driving specifications. Further, when load tests are available,...

Axial Capacity of Steel Pipe Piles in Clay
Development of theories for the prediction of the axial compressive and tensile load capacities of driven piles is made difficult by a variety of factors, e.g., disturbance of the soil...

Offshore Technology in Civil Engineering
Hall of Fame Papers from the Early Years
Prepared by the Program Committee of the Offshore Technology Conference of the Coasts, Oceans, Ports, and Rivers Institute of ASCE. This series presents...

Application of Model Pile Tests to Axial Pile Design
Experiments conducted with instrumented model pile segment probes at Harvey and Empire, Louisiana are summarized and the observed behavior interpreted. Correlations are developed for the...

Case Study of Offshore Pile System Reliability
This paper presents the results of research effort to evaluate the reliability of offshore pile foundation systems. It is an extension of previous work by the authors [14] dealing with...

Offshore Platform Steel Specification
The discovery in the 1980's of local brittle zones (LBZ's) in and near the heat-affected zone (HAZ) of the fabrication welds in certain offshore platform steels...

Design and Installation of Auger Steel Catenary Risers
The Auger export pipelines are connected to the TLP by steel catenary risers (SCRs). This is believed to be the first time steel pipe has been used for catenary risers. SCRs offer advantages...

Dynamic Response of Laterally-Loaded Piles in Centrifuge

 

 

 

 

Return to search