Room To Grow
The Victoria and Albert Museum, London’s renowned decorative arts and design museum, has unveiled a new, expansive underground exhibition gallery topped by an elegant courtyard. The need to maximize the...

As I See It: Rethinking the One-Third Increase in Bearing Capacity for Seismic and Wind

Calibration of Jackup Leg Foundation Model Using Full-Scale Structural Measurements
The fitness of jack-up rigs to operate in varying water depths and weather conditions is determined by "site-specific" structural assessments. These assessments are conducted by a wide range of companies...

Optimized Drilled Shaft Design through Post-Grouting: Shorten That Shaft for Better Performance
Tip post-grouting is a technique used to inject, under pressure, a neat cement grout beneath the base of a drilled shaft. This method enhances or improves axial load-displacement performance by increasing...

Cracking the Nuclear Code: Finding an Alternative to the Nuclear Density Gauge
Two of the most basic quality control tests made in the field during soil construction are the soil’s moisture content and density. The establishment of a uniform procedure to compare the performance of...

A Faculty Internship: Reconnecting with the Profession
After spending eight years as a full-time academic administrator at Lafayette College in Easton, PA – one of only a handful of institutions where discipline-specific engineering programs are embedded in...

Geotechnical Aspects of Pavements: There's More to Roads than Asphalt and Concrete!
When you jump on the highway to make that commute to work, do you think much about what's under the surface you ride on? Pavements are layered systems designed to provide a strong structure to support...

Design Considerations Common To All Permeable Pavements
Impervious cover in watersheds without controls result in increased stormwater runoff and decreased groundwater recharge in response to rainfall events. This increased runoff can be the...

Pervious Concrete
Pervious concrete consists of a hydraulic cementitious binding system combined with an open-graded aggregate to produce a rigid pavement with typically 15% to 25% interconnected void space....

General
Design of Latticed Steel Transmission Structures specifies requirements for the design, fabrication, and testing of members and connections for electrical transmission structures. These...

Loading, Geometry, and Analysis
This Standard applies to latticed steel transmission structures. These structures shall be either self-supporting or guyed. They consist of hot-rolled or cold-formed prismatic members...

Design of Connections
Bolted connections for transmission structures are normally designed as bearing type connections. It is assumed that bolts connecting one member to another carry the load in the connection...

Pipe Characteristics
Microtunneling pipe should meet the following general requirements: Circular shape with a flush outside surface (including at the joints); Strength sufficient to withstand both the installation...

Pipe Design
The pipes and joints, once installed, must be capable of safely withstanding, for the project design life, all in-use service loads, including those associated with the following factors:...

Extreme Wave-Force Calculation Procedure for 20th Edition of API RP-2A
The paper describes the revised guideline design wave force calculation procedure approved for the 20th edition of the API-RP2A WSD and the first edition of the API-RP2A LRFD and contrasts...

Performance Limits for Deepwater Pipelines
This paper highlights the differences between onshore and offshore pipeline design. It then summarizes the results of combined external pressure, tension, and bending testing on full scale...

A Simple Model to Predict Soil Resistance to Driving for Long Piles in Deepwater Normally Consolidated Clays
As the exploration and development for offshore oil and gas reserves moves into the deepwater environment of the continental slope, a good model is necessary to evaluate drivability of...

Findings From a Joint Industry Study on Foundation Fixity of Jackup Units
During the design storm conditions the soil supporting jack-up unit footings may be close to, or at plastic failure. Accordingly, the use of elastic solutions to the problems of foundation...

Axial Capacity of Steel Pipe Piles in Clay
Development of theories for the prediction of the axial compressive and tensile load capacities of driven piles is made difficult by a variety of factors, e.g., disturbance of the soil...

Calculated Examples of Long-Span Bridge Response to Wind

 

 

 

 

Return to search